Accessories, Options/accessories – Lincoln Electric COMMANDER 400 SVM133-B Manuel d'utilisation
Page 28
OPTIONS/ACCESSORIES
The following options/accessories are available for
your Commander 400 from your local Lincoln
Distributor.
K802R Power Plug Kit - Provides a plug for each
receptacle. The kit includes 4-120V plugs rated at 15
Amps each and 1-120V/240V Full-KVA plug rated at 50
Amps.
K857 28 ft. (8.5 m) or K857-1 100 ft. (30.4 m) Remote
Control - Portable control provides same dial range as
the output control on the welder from a location up to
the specified length from the welder. Has convenient
plug for easy connection to the welder. The
Commander 400 is equipped with a 6 pin connector for
connecting the remote control and a toggle switch for
selecting “LOCAL” output control or “REMOTE” output
control.
K704 Accessory Kit - Includes 35 feet (10 m) of elec-
trode cable and 30 feet (9 m) of work cable, head
shield, work clamp and electrode holder. Cable is
rated at 500 amps, 60% duty cycle.
K953-1 Two Wheel Trailer - For road, in-plant and
yard towing. Road towing with optional fender & light
kit. (For highway use, consult applicable federal, state
and local laws regarding possible additional require-
ments.)
K953-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-1 Fender & Light Kit
K965-1 Cable Storage Rack
K825-1 Ether Start Kit - Provides maximum cold
weather starting assistance for frequent starting below
10
o
F (-12.2
o
C). Required Ether tank is not provided
with kit.
K899-1 Spark Arrestor Kit - Easily mounts to stan-
dard muffler.
K949-1 Oil Drain Kit - Includes ball valve, hose and
clamp.
STICK WELDING
K704 Accessory Kit which includes:
• Electrode holder and cable.
• Ground clamp and cable.
• Head shield.
TIG WELDING
Magnum TIG Torch
Magnum Parts Kit and Argon gas
K930-1 TIG Module (not required for scratch
start DC TIG welding)
K936-3 Control Cable
K870 Foot Amptrol
Also available:
K963 Hand Amptrol
K814 Arc Start Switch
K937-22 Control Cable Extension
K937-45 Control Cable Extension
K844-1 Water Valve
HIGH FREQUENCY
GENERATORS FOR TIG
APPLICATIONS
The K799 Hi-Freq Unit and the K930-1 TIG Module are
suitable for use with the Commander 400. The
Commander is equipped with the required R.F. bypass
circuitry for the connection of high frequency generat-
ing equipment. The high frequency bypass network
supplied with the K799 Hi-Freq Unit does NOT need
to be installed into the Commander 400.
The Commander 400 and any high frequency generat-
ing equipment must be properly grounded. See the
K799 Hi-Freq Unit and the K930-1 TIG Module operat-
ing manuals for complete instructions on installation,
operation, and maintenance.
SEMIAUTOMATIC WELDING ACCESSORIES
LN-25 Wire Feeder - This portable wire feeder is capa-
ble of CC/CV wire feed welding.
LN-7 or LN-8 Wire Feeders - Semiautomatic, constant
speed wire feeder. For CV operation only.
LN-23P Wire Feeder - This portable wire feeder is
capable of CV operation. K350-1 adapter kit is
required.
NOTE: Gas-shielded welding requires a Magnum Gun.
Gasless welding requires an Inner shield Gun.
Magnum Spool Gun (K487-25) - A lightweight, semi-
automatic wire feeder for aluminum welding with argon
gas. Has built-in remote wire speed control in the han-
dle. Requires the K488 SG Control Module with appro-
priate control cable. Includes 25 feet (7.6 meters) of
power cable.
ACCESSORIES
C-2
C-2
COMMANDER 400