Document Outline

• 1. Introduction
  • 1.1 System Controller
  • 1.2 UPS Module (10 kVA / 8 kW)
  • 1.3 Static Switch (ST/SW) Module
  • 1.4 Battery
• 2. Operating Modes
  • 2.1 Normal Operation
  • 2.2 Battery Operation
  • 2.3 Bypass Operation
  • 2.4 Maintenance Bypass
• 3. User Interface
  • 3.1 Control Panel
  • 3.2 UPS Module Panel
  • 3.3 Static Switch Panel
  • 3.4 POWER+ Control screen
    • 3.4.1 Load-level bar graph
  • 3.5 Navigation and Operation Keypad
  • 3.6 Status Indicators
  • 3.7 Operation Buttons
  • 3.8 Network Access Indicator
  • 3.9 POWER+ Operation Modes
    • 3.9.1 Normal Operation
    • 3.9.2 Battery Operation
    • 3.9.3 Bypass Operation (Automatic)
    • 3.9.4 Bypass Operation (Manual)
    • 3.9.5 Emergency Power Off - EPO (Manual)
• 4. Installation Preparations
  • 4.1 Ac Input/Output Main Terminals
  • 4.2 Preparation
  • 4.3 The Power+ always requires a neutral line
    • 4.3.1 A 4-pole switch might disconnect the neutral line
• 5. System Installation
  • 5.1 Cabling
  • 5.2 Over-Voltage Protection
  • 5.3 Fuses
    • 5.3.1 AC INPUT FUSES
    • 5.3.2 DC DISTRIBUTION FUSES
  • 5.4 Special Terminal Connections
    • 5.4.1 Special Terminal Connections on 50 kVA Units
    • 5.4.2 Special Terminal Connections on 100 kVA Units
    • 5.4.3 Load on Bypass Alarm
    • 5.4.4 Battery Trip Coil
    • 5.4.5 Emergency Power-off
  • 5.5 Inspections to be performed prior to installation
  • 5.6 Installation Procedure
  • 5.7 First-time Startup
  • 5.8 Checks to be performed following initial startup
  • 5.9 Configuration
    • 5.9.1 Check Configured Modules
    • 5.9.2 Check Total Ampere-Hours
    • 5.9.3 Set Date and Time and Serial Number
    • 5.9.4 Define the IP Address of the Power+
  • 5.10 Testing
    • 5.10.1 Blackout Test
    • 5.10.2 Cold Start
    • 5.10.3 Test Under Load
    • 5.10.4 Check IP Communication with Controller
    • 5.10.5 Test Wing Option
• 6. POWER+ routine start-up
  • 6.1 POWER+ Shutdown (Switching to Bypass)
  • 6.2 POWER+ Total Shutdown (No Ac Output)
• 7. POWER+ Control Panel
• 8. Power+ Menu Functions in Detail
  • 8.1 Main Menu
  • 8.2 “System” Option
  • 8.3 “UPS module” Option
  • 8.4 “Self-test” Option
  • 8.5 “History” (logs) Option
  • 8.6 “Battery” Option
  • 8.7 “Alarm” Option
  • 8.8 “Setup – Alarm Set” Option
    • 8.8.1 Setting Ac Voltage Alarms
    • 8.8.2 Setting Battery Floating Voltage Alarm
    • 8.8.3 Setting Battery Over/Under Temperature Alarms
    • 8.8.4 Setting Battery Integration Alarm
  • 8.9 “Setup – Module Conf.” Option
    • 8.9.1 Setting Number of Phases
    • 8.9.2 Setting Module/s Frequency
    • 8.9.3 Setting Module/s Voltage
    • 8.9.4 Update Voltage/Frequency/Phase
    • 8.9.5 Output Adjustment
    • 8.9.6 Setting Frequency Limits
    • 8.9.7 Calibrating DC Voltage
    • 8.9.8 Calibrating AC Voltage
  • 8.10 “Setup – Battery” Option
    • 8.10.1 Setting Battery Test Voltage
    • 8.10.2 Setting Battery Test Voltage Alarm
    • 8.10.3 Setting Battery Current Limit
    • 8.10.4 Enable/Disable Battery Current Limit
    • 8.10.5 Setting Temperature Compensation
    • 8.10.6 Setting Disable Temperature Compensation
    • 8.10.7 Setting Absolute Maximum and Minimum Voltages
    • 8.10.8 Activating the Battery Test
    • 8.10.9 Setting the Automatic Battery Test Period
    • 8.10.10 Setting the Automatic Battery Test Top Time
    • 8.10.11 Setting the Nth Battery Capacity
    • 8.10.12 Activating ‘Auto’ Test
    • 8.10.13 Enabling/Disabling Options
  • 8.11 Setup – Charge, Time, Site, and Password Options
    • 8.11.1 Setting the Floating Charge
    • 8.11.2 Setting the Time
    • 8.11.3 Setting the Site Number
    • 8.11.4 Changing the Password
  • 8.12 “Setup – “Service” Option
    • 8.12.1 Setting UPSs
    • 8.12.2 Testing Dry Output Relays
    • 8.12.3 Configuring the UPS
      • 8.12.3.1 Number of Redundant UPSs
      • 8.12.3.2 Total Number of UPSs
      • 8.12.3.3 Total Number of Batteries
      • 8.12.3.4 Setting up the Static Switch
      • 8.12.3.5 Setting up the Dry Alarms
      • 8.12.3.6 Calibrating DC Currents
      • 8.12.3.7 Selecting Standalone or Parallel Operation
      • 8.12.3.8 Enabling/Disabling Remote Commands
    • 8.12.4 Enabling/Disabling Current Sharing
    • 8.12.5 Setting Power Factor Correction
    • 8.12.6 Setting the SC2012
  • 8.13 “Setup – “Silicon” Option
  • 8.14 “Static Switch” option
  • 8.15 System Controller Setup Verification
    • 8.15.1 Setup Verification Menu
    • 8.15.2 Connection Status of UPSs
    • 8.15.3 On/Off Status of UPSs
    • 8.15.4 Software and Communication Revision
    • 8.15.5 Network Parameters
    • 8.15.6 Dry Input and Output Relay Contact Status
    • 8.15.7 Alarms Status
    • 8.15.8 Setting the Menu Language
    • 8.15.9 System Parameter Settings
      • 8.15.9.1 First General Screen
      • 8.15.9.2 Second General Screen
      • 8.15.9.3 Third General Screen
      • 8.15.9.4 Fourth General Screen
• 9. The Power+ built-in Web interface
  • 9.1 Preliminaries to use of the Web interface
  • 9.2 Main Screen
  • 9.3 The Main Menu and its options
    • 9.3.1 “Analysis” main menu option
    • 9.3.2 “Modules” main menu option
    • 9.3.3 “STSW” (Static Switch) main menu option
    • 9.3.4 “Log” main menu option
    • 9.3.5 “Control” main menu option
    • 9.3.6 “SMS” main menu option
    • 9.3.7 “Configuration” main menu option
      • 9.3.7.1 Network configuration
      • 9.3.7.2 “Date and time” – setting the calendar and clock
      • 9.3.7.3 Set user name and password
      • 9.3.7.4 SNMP security
      • 9.3.7.5 SNMP trap targets
      • 9.3.7.6 Shutdown Targets
      • 9.3.7.7 Defining email notification targets
      • 9.3.7.8 Defining SMS notifications
• 10. SNMP Agent (option)
• 11. Wing: Wireless Control (option)
  • 11.1 Installing the Wing
• 12. POWER+ Specifications