Accessories – Lincoln Electric VANTAGE SVM178-B Manuel d'utilisation
Page 67
ACCESSORIES
C2.3
C2.3
VANTAGE® 500
TIG OPTIONS
K1783-9 PTA-26V TIG Torch
Air Cooled 200 amp torch (2 piece) equipped with valve
for gas flow control. 25 ft. (7.6m) length.
KP509 Magnum Parts Kit for PTA-26V TIG Torch
Magnum Parts Kit provides all the torch accessories
you need to start welding. Parts kit provides collets,
collet bodies, a black cap, alumina nozzles and tung-
stens in a variety of sizes, all packaged in an easy to
carry reclosable sack.
K870 Foot Amptrol®-Varies current while welding for
making critical TIG welds and crater filling. Depress
pedal to increase current. Depressing pedal fully
achieves maximum set current. Fully raising the pedal
finishes the weld and starts the after flow cycle on sys-
tems so equipped. Includes 25 ft. (7.6m) control cable.
K963-3 Hand Amptrol®-Varies current for making crit-
ical TIG welds. Fastens to the torch for convenient
thumb control. Comes with a 25 ft. (7.6m) cable. (One
size fits all Pro-Torch TIG Torches.)
K2347-1 Precision TIG 185 Ready-Pak
For AC TIG Welding with square wave performance
use the AC generator of the Engine-Driven Welder to
supply the power. Easy setup. Includes torch, foot
amptrol, gas regulator and hose. Requires the K1816-
1 Full KVA adapter kit.
K2350-1 Invertec® V205-T AC/DC One-Pak™ Package
For AC TIG welding with square wave performance,
use the AC generator of the engine-driven welder to
supply the power. Easy setup. Includes torch, parts
kit, regulator and hose kit, Twist-Mate™ torch adapter,
work cable with Twist-Mate end and foot Amptrol®.
HIGH FREQUENCY GENERATORS FOR
TIG APPLICATIONS
The K799 Hi-Freq Unit and the K930- [ ] TIG Modules
are suitable for use with the Vantage 500. The Vantage
500 is equipped with the required RF bypass circuitry
for the connection of high frequency generating equip-
ment. The high frequency bypass network supplied
with the K799 Hi-Freq Unit does NOT need to be
installed into the Vantage 500.
The Vantage 500 and any high frequency-generating
equipment must be properly grounded. See the K799
Hi-Freq Unit and the K930-AII TIG Module operating
manuals for complete instructions on installation, oper-
ation, and maintenance.
WIRE FEEDER OPTIONS
K449 LN-25 Wire Feeder
Portable CC/CV unit for flux-cored and MIG welding.
Includes Gas Solenoid & Internal Contactor.
K126-2 Magnum® 350 Innershield Gun (for LN-25)
For self-shielded wire with 15 ft. (4.5m) cable. For
.062-3/32” (1.6-2.4mm) wire.
KP653-3/32 Drive Roll and Guide Tube Kit (for LN-25)
For .068-3/32” (1.8-2.4mm) cored or solid steel wire.
K1802-1 Magnum® 300 MIG Gun
For .035-.045 (0.9-1.2mm) gas shielded wire. Includes
15 ft. gun and cable assembly and connector kit.
KP653-035S Drive Roll and Guide Tube Kit (for LN-25)
For .035-.040” (0.9-1.0mm) solid steel wire.
K2613-1 LN-25 PRO PORTABLE WIRE FEEDER-The
MAXTRAC® wire drive enhances performance, while the
replacement case, and many other upgrade options that can
be installed in less then five minutes aid in the serviceability.
KP1697-5/64 Drive Roll Kit- Includes: 2 polished U
groove drive rolls, outer wire guide and inner wire guide
for solid core wire. (Used on LN-25 Pro)
KP1697-068 Drive Roll Kit- Includes: 2 polished U
groove drive rolls, outer wire guide and inner wire guide
for solid core wire. (Used on LN-25 Pro)
KP1696-1 Drive Roll Kit- Includes: 2 V groove drive
rolls and inner wire guide for Steel Wires. (Used on LN-
25 Pro)
K487-25 Magnum SG Spool Gun
Hand held semiautomatic wire feeder. Requires SG
Control Module and Input Cable.
K488 SG Control Module
The Interface between the power source and the spool
gun. Provides control of the wire speed and gas flow.
For use with a spool gun.
K691-10 Input Cable (For SG Control Module)
For Lincoln engine power sources with 14-pin MS-type
connection, separate 115V NEMA receptacles and out-
put stud connections.
OTHER WIRE FEEDERS USABLE WITH
THE VANTAGE 500
• NA-3 or LT-7 Automatic Wire Feeder
• LN-742 Semi-automatic Wire Feeder
• LF-72/74 Semi-automatic Wire feeder
• LN-7 Semi-automatic Wire Feeder
• LN-8 Semi-automatic Wire Feeder
• LN-23P Semi-automatic Wire Feeder
• LN-15 Semi-automatic Wire Feeder
See the Wire Feeder Manual or the Diagrams section
of this manual for connection information of the various
feeders to the Vantage 500.