Sony MHC-C9EX - Manuel (Page 18)

6
If the indicator ior the side you want to
start recording does not light, press [>
or <1 to light the side to start recording.
If it lights, skip to step 7.
7
Press II PAUSE on the tape player to
release recording pause.
Recording starts. You can also start
recording by pressing [> or <1 .
To stop recording
Press ■ .
When recording AM broadcasts
Sometimes a whistling sound not normally
heard when just listening to a broadcast is
audible. If this happens, adjust the position
of the AM loop antenna until the whistling
sound can no longer be heard.
To activate DOLBY NR
When you want to reduce the hiss noise in
low-level high-frequency signals, set
EHDLBY NR to B or C after step4.
Adjusting the volume will not affect the
recording level
But this control will change the sound
1 O levels you hear through speakers or
headphones.
-» continued
Recording From
Another Tape
(dubbing)
Dubbing Another Tape
Automatically
You can record the whole tape onto another
automatically. While dubbing, you can
listen to the radio or a CD by selecting
TUNER or CD. Use the buttons on the unit
to do this operation and any type of tape
for dubbing.
4
1
2
1 Press = and insert a recorded tape in
deck A and a blank tape in deck B.
Use or ►► on deck A to locate the
beginning of the track that you want to
record.
2
Choose how you want the tape to record
and set DIRECTION to the mode you
want.
Position Operation
^ * Dubbing stops at the end of
one side.
cna When the tape in one deck
comes to the end of the
front side, it reverses
immediately regardless of
the tape position in the
other deck.
RELAY When the tape in one deck
reaches its end of the front
side, it stops until the other
tape come to its end, and
then both tapes reverse
together.
3
Press NORMAL or HIGH.
NORMAL : dubbing at normal speed
HIGH: dubbing at high speed
Deck B enters the recording pause
mode.
4
Choose the same direction on both
decks by pressing O- or <1.
To dub on one side, choose O- or <3.
To dub on both sides, choose [>.
5
Press II PAUSE.
The tape starts dubbing.
When the tape has started dubbing from
the reverse side in mode, dubbing
will stop at the end of the reverse side.
To stop dubbing
In normal dubbing, press ■ on deck B. In
high-speed dubbing, press ■ on both deck
A and deck B.
You do not have to set DOLBY NR
The tape in deck B is automatically
recorded in the same state as the tape in
deck A.
Listening to another audio source while
dubbing is in progress
Select the sound source that you want to
listen to, using the FUNCTION button on
the unit. You can monitor the material
being dubbed by selecting TAPE.
During high-speed dubbing
None of the buttons on either deck works,
except for the ■ button.
Dubbing Another Tape
Manually
You can record the sound that you have
adjusted. Use the buttons on the unit to do
this operation and any type of tape for
dubbing.
2
5
6
1
4
1 Press = and insert a recorded tape in
deck A and a blank tape in deck B.
Use or ►► on deck A to locate the
beginning of the track that you want to
record.
2
Press FUNCTION to select the tape
player.
3
Select dual or single-sided recording.
To record Set DIRECTION to
One side
Both sides* crp or RELAY
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
4
Set DOLBY NR.
To record in the same state as the tape in
deck A: OFF
To set DOLBY
NR for a tape recorded
with DOLBY OFF: B or C
5
Press 9 REC.
Deck B stands by for recording.
The O (for front side) or <3 (for
reverse side) indicator lights steadily to
show you which side will start
recording. The other indicator flashes
for a few seconds, then disappears.
6
If the indicator for the side you want to
start recording does not light, press O
or <] to light the side to start recording.
If it lights, skip to step 7.
7
Press II PAUSE on the tape player to
release recording pause.
Recording starts. You can also start
recording by pressing or <3.
To stop recording
Press ■ on the both decks.
Note
•Do not press FUNCTION to select the CD
player or tuner while dubbing manually.
Chapter 4: the Tape Player