53 creating a patch, D beam – Roland Piano Manuel d'utilisation
Page 53
53
Creating a Patch
Creating a Patch
BEND UP:
Raises the pitch in semitone steps (up to 4 octaves
higher).
BEND DOWN:
Lowers the pitch in semitone steps (up to 4 octaves
lower).
AFTERTOUCH:
Aftertouch
OCT UP:
Raises the key range in octave steps (up to 3 octaves
higher).
OCT DOWN:
Lowers the key range in octave steps (up to 3 octaves
lower).
TRNS UP:
Raises the key range in semitone steps (up to 6 semitones
higher).
TRNS DOWN:
Lowers the key range in semitone steps (up to 5
semitones lower).
TAP TEMPO:
Tap tempo (a tempo specified by the interval at which
you press the button).
MONO/POLY:
Pressed to toggle between polyphonic (POLY) and
monophonic (MONO) play of a patch.
ARP HOLD:
Switch between Hold On/Hold Off for the Arpeggiator
performance.
Mode 1–4 (Realtime Control Button Mode 1–4)
Specify how the [
]–[
] buttons are to operate.
Value
MOMENTARY:
The button will be on only while you are pressing
(holding) it, and will be off when you release your finger from the
button.
LATCH:
The button will switch on/off each time you press it.
D Beam
Switch (D Beam Switch)
Switches the D Beam controller on/off.
Value:
OFF, ON
Assign (D Beam Assign)
Specifies the function controlled by the D Beam controller.
Value
OFF:
The D Beam controller will not be used.
CC01–31, 33–95:
Controller numbers 1–31, 33–95
For more information about Control Change messages, please
refer to
“MIDI Implementation”
(Sound/Parameter List).
BEND UP:
Raises the pitch in semitone steps (up to 4 octaves
higher).
BEND DOWN:
Lowers the pitch in semitone steps (up to 4 octaves
lower).
AFTERTOUCH:
Aftertouch
NOTE:
Play the sound of the most recently pressed key.
OCT UP:
Raises the key range in octave steps (up to 3 octaves
higher).
OCT DOWN:
Lowers the key range in octave steps (up to 3 octaves
lower).
START/STOP:
Starts/Stops the sequencer.
TAP TEMPO:
Tap tempo (a tempo specified by the interval at which
you move your hand over the D Beam controller).
ARP SWITCH:
Switches the Arpeggiator on/off.
ARP VAR:
Arpeggio Variation
ARP ACCENT:
Arpeggio Accent Rate
ARP SHFFLE:
Arpeggio Shuffle Rate
ARP OCT UP:
The range in which the arpeggio is sounded will rise
in steps of an octave (maximum 3 octaves).
ARP OCT DW:
The range in which the arpeggio is sounded will
lower in steps of an octave (maximum 3 octaves).
Polarity (D Beam Polarity)
Switch the polarity of the D Beam controller.
With a setting of “REVERSE,” the direction of control for the D Beam
controller will be inverted.
Range
: STANDARD, REVERSE
Range Lower (D Beam Range Lower)
Specify the lower limit of the range of the D Beam controller. Values
below this setting will not be output.
Value:
0–UPPER
Range Upper (D Beam Range Upper)
Specify the upper limit of the range of the D Beam controller. Values
above this setting will not be output.
Value:
LOWER–127
Setting Effects for a Patch (Effects/
MFX/MFX Control/Chorus/Reverb)
For details regarding effect settings, refer to the pages shown
below.
•
“Applying Effects in Patch Mode”
•
“Making Multi-Effects Settings (MFX/MFX Control)”
•
“Making Chorus Settings (Chorus)”
•