Roland Piano - Manuel (Page 150)

150
Editing Songs
Channel (MIDI Channel)
Selects the MIDI channel(s) of the data to be extracted.
To extract all sequencer data, set this parameter to ALL. To extract
just the sequencer data of a specific MIDI channel, select that MIDI
channel.
Value: ALL, 1–16
If you set the Status parameter to “EXC,” “TUNE” or “PTN,” the
Channel parameter will not be available.
8. When you have finished making settings, press [8 (Execute)]
to execute the operation.
Shifting Performance Data Forward
and Back (Shift Clock)
This function shifts the timing of sequencer data backward or
forward in time within a specified area in steps of 1 clock. Slight
shifts of timing can speed up or drag performance.
When this function is executed, data that would be moved to a
point before the beginning of the song will automatically shift to
the beginning of the song. If data would be moved to a point
past the end of the song, additional new measures will be
created automatically as needed. The time signature of the newly
created measures will be the same as that of the measure
immediately preceding.
1. Access the Song Edit screen, and then load the song you
want to edit (p. 136).
2. Press [8 (Track Edit)].
The Track Edit window appears.
3. Press or to select “Shift Clock,” and then press [8
(Select)].
A message of “SHIFT CLOCK: Select target point.” appears.
4. Use [CURSOR] to move the cursor to the first measure of the
track or pattern whose sequencer data you want to move. If
you want to specify all tracks, press [7 (TrkAll)].
5. Hold down [SHIFT] and press to move the cursor to the
last measure of the track or pattern whose sequencer data
you want to move, and press [8 (Select)] to specify it.
The Track Edit (Shift Clock) window appears.
fig.11-25_50
6. Use [CURSOR] to move the cursor to the desired parameter,
and turn the VALUE dial or press [INC]/[DEC] to make the
setting. First check the region that is to be affected by the
operation, and correct it if necessary.
Track
Check/modify the track(s) or pattern whose sequencer data will be
moved in units of one clock.
Value
ALL: Phrase tracks 1–16, the beat track, and the tempo track
TRK 1–TRK 16: The specified phrase track
TEMPO: Tempo clock
PTN001–PTN100: The specified pattern
Measure, for (Edit Range)
Check/modify the range of measures in which the sequencer data
will be moved in units of one clock. If you set “for” to “ALL,” all
measures will be specified.
Bias
Specify the amount (number of clocks) by which the sequencer data
will be moved.
Value: -4800– +4800
Status
Selects the type of data to be shifted in time.
Value
ALL: All types of sequencer data
NOTE: Note
P.AFT: Polyphonic Aftertouch
C.C: Controller numbers
PROG: Program numbers
C.AFT: Channel Aftertouch
BEND: Pitch Bend
EXC: System Exclusive messages
Tune: Tune Request
PTN: Pattern Call Message data
If the Track parameter is set to “TEMPO,” the Status parameter
will not be available.
Range
If you set the Status parameter to “NOTE,” “P.AFT,” “C.C,” or
“PROG,” specify the range of data. Specify the minimum value of
the range at the left, and the maximum value at the right.
• To shift all Note or Polyphonic Aftertouch data, set “C1–G9.” To
shift the timing of C4 Note/Polyphonic Aftertouch data, specify
“C4–C4.” To shift the timing of Note/Polyphonic Aftertouch
data from C3 to C4, specify “C3–C4.”
• If you want to shift all controller numbers, set this to “0–127.” If
you want to move all program numbers, set this to “1–128.” To
shift the timing of number 4, specify “4–4.” To shift the timing of
numbers from 3 to 14, specify “3–14.”