Canon CD-300 Manuel d'utilisation

Page 33

Attention! Le texte de ce document a été détectée automatiquement. Pour consulter le document original, vous pouvez utiliser le mode "Original".

Advertising
background image

9

pflm

:

button

To fiturn to (huntHuill fUtfilay : Pivts Previnv button

6.

Press the Print button.

The printer begins printing. All three mode lamps
flash while printing is in progress.

• If you wish to stop printing before all images

have been printed, press the Clear button.

The printer will finish printing the image it is
working on, and then stop.

• If you are printing a single image to panorama

paper with the Crop setting on, the printer

will crop the image respectively.

MEMO

The printer can create horizontal panoramas only.
The printer may not be able to create a panorama

if overlap of adjoining images is too large (ex­

ceeding half the image size) or extremely small.

Panorama results produced by the CD-300 may
be somewhat different from results obtained us­
ing commercially available panorama software.

If you wish to merge and print a panorama im­

age using a Ink Cassette for Standard, you need

to follow a slightly different procedure. First, make

sure that the printer is in Memory Card mode.

Then select [Options] from the menu, press the

Enter/Memory button, select [Panorama] from the

submenu, and press the Enter/Memory button
again. Then continue from Step 4 above.

If you replace the Ink Cassette for Panorama with

a Ink Cassette for Standard after you have set

up the panorama, you can proceed to print the
panorama image onto the standard paper. In this

case, the Menu area will show only [Copies],

[Adjust], [Crop], and [Back]. If you wish to cancel

the panorama print, select [Back] and then press

the Enter/Memory button.

6.

Appuyez sur la touche Print.

L'impression commence. Pendant l'impression,

les trois témoins de mode clignotent.

• Pour arrêter l'impression, appuyez sur la tou­

che Clear.

Si vous appuyez sur la touche Clear, l'image

en cours d'impression est impriméejusqu'â la
fin et l'imprimante s'arrête après cette image.

• Si vous imprimez une seule image sur un papier au

format panorama avec la fonction de rognage en
service, l'imprimante coupera l'image sans tenir
compte du réglage de rognage actuel.

L’imprimante ne peut créer que des panoramas
horizontaux.
L’imprimante peut ne pas pouvoir créer une

image panorama si la zone de chevauchement

de deux images adjacentes est trop grande

(dépassant la moitié de la taille de l’image) ou

extrêmement petite.

Les résultats de l’image panorama produite par
la CD-300 peuvent être parfois différente des
résultats obtenus à l’aide d’un logiciel panorama

en vente dans le commerce.

Si vous souhaitez fusionner et imprimer une
image panorama en utilisant la cassette d’enae pour
papier standard, vous devez suivre une procédure
légèrement différente. Vérifiez que l’imprimante est

en mode de carte à mémoire, choisissez [Options]
dans le menu, et [Panorama], et appuyer de nouveau
sur Enter/Memory, puis réalisez la procédure
ci-dessus à partir de l’étape 4.
Si vous remplacez la cassette d’encre pour papier

panorama parla cassette d’encre pour papier stan­

dard après avoir créé l’image panorama, vous

pouvez imprimer l’image panorama sur un papier

standard. Dans ce cas, la zone des menus

indiquera seulement les boutons [Copies], [Adjust],

[Crop] et [Back]. Si vous souhaitez annuler

l’impression panorama, choisissez le bouton [Back]

et appuyez sur la touche Enter/Memory.

31

Advertising