Pioneer VSX-C501-S - Manuel (Page 34)

Using the tuner 07
34
En
1 Press SEARCH.
2 Use the / (cursor left/right) buttons to select
the program type you want to hear.
3 Press ENTER to search for the program type.
The tuner searches through the FM stations stored in the
station memories.
If the tuner finds a matching program type, the tuner
plays 5 seconds of the station. To listen to that station,
press the
ENTER button. (The tuner stops searching.)
If you don’t press the ENTER button during the above
mentioned 5 seconds, the tuner resumes the search.
When the tuner finds a program type you searched for,
the frequency display will blink for about 5 seconds and
then the display will show
FINISH briefly.
If NO PTY is displayed it means the tuner couldn’t find
that program type at the time of the search.
Note
• This function searches RDS stations preset in the 30-
station memory. If there are no station presets, or if
the program type could not be found among the
station presets
NO PTY is displayed.
Enhanced Other Network (EON)
EON (Enhanced Other Network information) allows you
to set the receiver to switch automatically to a news or
traffic information broadcast. Once set, the receiver will
scan for stations transmitting news or traffic
announcements even when it’s in a different input
function (
DVD , for example). When the broadcast ends,
the tuner returns to the original frequency or input
function.
EON can only be used in areas where EON data is
transmitted, and it only works with FM broadcast stations
that transmit RDS program type (PTY) information.
The EON indicator lights when EON is set. The dot
indicator to the left lights when the current broadcast
carries the EON data service.
1 Press the FM/AM button to put the receiver in FM
tuner mode.
2 Press EON to select the EON mode.
Press repeatedly to switch between:
• TA (Traffic Announcement) – Sets the tuner to pick
up traffic information when it is broadcast.
• NEWS – Sets the tuner to pick up news when it is
broadcast.
• OFF – Switches off the EON feature.
When set to TA or NEWS , the EON indicator in the
display lights. When the receiver switches automatically
to an EON broadcast, the dot indicator blinks.
Note
• The EON function does not work when listening to
AM reception, or when the AV Direct function is on
(see
The AV Direct mode on page 10 and AV Direct
setting on page 40).
• Simultaneous requests for Traffic Information ( TA )
and News ( NEWS ) is not possible.
• When EON is turned on and a function other than the
tuner is selected, the function will switch to the FM
station automatically when Traffic Information or
News begins. When the program ends, the original
function will be restored.
• You can’t use the T.EDIT and SEARCH buttons while
the EON indicator in the display is lit.
• You can’t change the input function while receiving
an EON broadcast. If you want to change to a source
other than tuner, press
EON and turn the EON mode
to OFF .
Program identification function
The receiver will automatically register an identifying
marker (called a PI code) for any station you input into
the memory classes which can receive RDS or EON data.
If you want to remove the currently memorized stations
from RDS and EON searches, you can do it by erasing the
PI codes.
1 Tune to the station for which you want to erase
the PI marker.
2 Press EON for two seconds or more.
ERASE PI is displayed.
3 Press ENTER within 5 seconds.
AUDIO
MODE DIALOG
MUTE
MASTER
VOLUME
DTV MENU
TOP MENU T.EDIT
MENU
GUIDE SEARCH
SUBTITLE
ROOM
SETUP
TUNE
TUNE
ST ST
SYSTEM SETUP
BAND EON RETURN RF ATT A
DISPLAY CLASS MPX D.ACCESS
ENTER
B C D E
DISC
ENTER
VIRTUAL SB
vsx-c501(WY).book 34 ページ ２００３年５月２２日 木曜日 午前１０時２９分