Pioneer VSX-C501-S - Manuel (Page 10)

Connecting your equipment 03
10
En
Note
• All AV connectors also have audio in. The VIDEO and
DVR/TV connectors also have audio out.
• The VIDEO and DVR/TV connectors are compatible
with i/o-Link.A, T-V Link, Easy Link, MegaLogic,
SMARTLINK, Q-Link, DATALOGIC, NextTView Link, etc.
5 SUBWOOFER OUT jack (page 16)
Connect a powered (active) subwoofer.
6 Digital connections
The three digital audio jacks are all inputs. Connect to the
digital outputs of digital source components such as
DVD and CD players, satellite receivers, etc.
STB(DVD) OPT1 jack (page 13)
Optical digital audio jack for the STB input (although
it is possible to reassign it to the DVD input).
DVR/TV OPT2 jack (page 14)
Optical digital audio jack for the DVR/TV input.
• When connecting optical cables, be careful when
inserting the plug not to damage the shutter
protecting the optical socket.
• When storing optical cable, coil loosely. The cable
may be damaged if bent around sharp corners.
DVD(STB) COAX jack (page 11)
Coaxial digital audio jack for the DVD input (although
it is possible to reassign it to the STB input).
7 AUDIO IN (5.1CH) jacks (page 11)
Multichannel analog audio inputs, mainly for use with
multichannel DVD-Audio discs, and some DVD-Video
discs that do not allow multichannel digital output.
8 AC IN (page 20)
Connect the supplied AC power cable.
The AV Direct mode
The AV Direct mode allows the receiver to pass audio/
video signals arriving at one of the AV connector inputs
to the AV connector outputs without the sound being
output through the speakers connected to the receiver.
This allows you to operate your other components as if
they were connected directly to each other without the
receiver being on. One use for this is if you want to record
from your satellite receiver to your VCR (both connected
to this receiver) without the receiver being switched on.
You could also use the AV Direct mode to watch a video,
using your TV’s speakers for the audio, without switching
on the receiver.
You can switch into AV Direct mode (from either standby
or on) using the
AV DIRECT button on the remote
control. However, it’s also possible to set the receiver to
switch the AV Direct function on automatically when an
incoming signal is detected. See also
AV Direct setting on
page 40.
The diagram below shows how the
AV DIRECT and the
STANDBY/ON buttons switch the receiver between
standby, AV Direct mode, and on.
Installing the receiver
• When installing this unit, make sure to put it on a
secure and level plane that is stable.
• Don’t place it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that gives
off a magnetic field). This may interfere with the
sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is a vibration or other
movement
– in places that are very dusty
– in places that have hot fumes or oils (such as a
kitchen)
When making cable connections
Be careful not to arrange cables in a manner that bends
the cables over the top of this unit. If the cables are laid
on top of the unit, the magnetic field produced by the
transformers in this unit may cause a humming noise to
come from the speakers.
Connector Input Output
DVD Composite, S-video,
RGB
–
STB Composite, S-video,
RGB
–
VIDEO Composite, S-video,
RGB
Composite
DVR/TV Composite Composite, S-video,
RGB
Standby
AV Direct On
RECEIVER
AV DIRECT
Standby
AV Direct On
vsx-c501(WY).book 10 ページ ２００３年５月２２日 木曜日 午前１０時２９分