Panasonic AJ-B95 - Manuel (Page 77)

77
1
Press the CORCT ([SHIFT] + [5]) button.
The changed data is stored in the EDL memory.
2
When the edit OUT point of VTR2 (recorder) has
been changed, a message (RIPPLE OK?) for
verifying whether to go ahead with ripple
processing appears.
If ripple processing is to be performed, press the
ENTER button.
If not, press the C button.
3
To perform ripple processing, input the event to be
executed next.
When ripple processing is to be performed for all
the events subsequent to an event whose data has
been changed, simply press the ENTER button.
To designate the events for which ripple
processing is to be performed, input the numbers
of the events using the numeric input buttons and
the [ ] button.
Example:
To designate events 5 to 21, press [5] “ [ ] “ [2] “
[1], and then press [ENTER].
CORCT/TRACK/DISP
Correction function (CORCT)
This function enables corrections to be made to edit
data in an existing event (one whose edit data has
already been stored in the memory) but not in a new
event.
1
Change the edit IN point of the VTR2 (recorder).
2
Press the TRACK ([SHIFT] + [6]) button to
establish the track mode.
O
The colon (:) between the hours and minutes on
the counter display shown on the monitor screen
changes to a dot (.) to indicate that the track
mode has been established.
O
The time code (UB or CTL) indicated on the
display tube flashes to indicate that the track
mode has been established.
O
The edit IN point of VTR1 (player) is
automatically changed in a way that reflects the
change which was made in step
1
.
3
When an edit IN point of VTR2 (recorder) is
changed while the track mode is established, the
edit IN point of VTR1 (player) is also changed
automatically in a way that reflects the VTR2
change.
4
The track mode is released when the edit IN point
of VTR1 (player) is changed.
<Note>
Since the track mode is automatically established
when ALL has been selected as the setup menu item
No.313 (AUTO ENTRY) setting, there is no need to
establish the track mode by pressing the TRACK
([SHIFT] + [6]) button.
Track function (TRACK)
This function is used to set the edit points of VTR1
(player) efficiently in response to a change made in an
edit IN point of the VTR2 (recorder).
Monitor display ON/OFF switching
(DISP)
The status, operation mode and other information
displays which are superimposed onto the monitor
(liquid crystal monitor, VIDEO MONITOR output) can
be switched from ON to OFF, or vice versa, by
pressing the DISP ([SHIFT] + [0]) button.
AUDIO MONITOR SELECT
L R
4
(V1·2) V1 V2
1
3
MIX
MIX
2
4
1
3
MIX
MIX
ASMBL
1ST EDIT
PREVIEW
VTR 2 VTR 1 SPLIT
MARK
OUT
MARK
IN
SHIFT ENTER ALL STOP
REVIEW
AUTO
EDIT
MULTI
GO TO
GO TO OUT
DUR
TOTAL
OUT
LAST ED
IN
LAST X
EVENT
7 8 9
4 5 6
1 2
0 C
3
~
-
+
DELETE
SET UP F/TC DIAG
LIST CORCT BS TRACK
DUMP LOAD FS
DISP EXIT RETURN
T SET
2 CH 1
POWER
OFF ON
UNI
VAR
CH 2 CH 3 CH 4
ANALOG
V1/V2
REC
ENTER C
DISP
([SHIFT] + [0])
TRACK
([SHIFT] + [6])
CORCT
([SHIFT] + [5])