Panasonic AJ-B95 - Manuel (Page 73)

73
LAST X/LAST ED/TOTAL
TOTAL ([SHIFT] + [DUR])
This button is for checking the total editing time.
The total editing time from the start of editing is
displayed.
This enables the editing time to be checked when
editing material with a fixed length.
O
Press the TOTAL ([SHIFT] + [DUR]) button. While
it is held down, the total editing time is shown in the
VTR2 time display area.
Start time and end time:
The time that serves as the reference for calculation is
determined by the edit point setting statuses, etc.
The total editing time is equal to the end time
prescribed below minus the start time.
Start time:
Normally, the VTR2 (recorder) IN point of the edit
data set in the first event of the EDL memory is the
start time.
End time:
The VTR2 (recorder) OUT point of the displayed
event is the end time.
When the OUT point has not been set, the VTR2
(recorder) IN point serves as the end time; when
not even the IN point has been set, the VTR2
(recorder) OUT point of the previous event serves
as the end time.
LAST ED ([SHIFT] + [OUT])
This button is for recalling the original data which
has been previewed and edited.
O
Press the LAST ED ([SHIFT] + [OUT]) button. The
original data which has been previewed and edited
is restored.
O
Pressing the LAST ED button again restores the
current edit data after the previous editing. Each
time the LAST ED button is pressed, the original
data and present edit data are displayed
alternately.
LAST ED buffer:
The data automatically stored in the LAST ED buffer
consists of the latest data stored in the EDL memory
and preview data before any changes are made.
When the LAST ED button is pressed, the data stored
in this buffer is recalled. This function comes in handy
when previewing the data before and after the
changes are made in case the pre-preview editing
data is more suited to the purpose at hand.
LAST X ([SHIFT] + [IN])
This button is for re-registering an event which
has been deleted.
A once deleted event can be re-registered.
O
Recall the deleted event (the one with the “d”
indication on the event number display area), and
press the LAST X ([SHIFT] + [IN]) button.
The “d” indication is replaced with a blank display.
AUDIO MONITOR SELECT
L R
CH 1
4
1
3 MIX
ANALOG
MIX
2
UNI
V2
PB
SDI REC
VAR
CH 2 CH 3 CH 4
CH 3 4
4
(V1·2) V1 V2
1
3 MIX
MIX
2
4
1
3 MIX
MIX
ASMBL V A1 A2
1ST EDIT
PREVIEW
VTR 2 VTR 1 SPLIT
MARK
OUT
MARK
IN
SHIFT ENTER ALL STOP
REVIEW
AUTO
EDIT
MULTI
GO TO
GO TO OUT
DUR
TOTAL
OUT
LAST ED
IN
LAST X
EVENT
7 8 9
4 5 6
1 2
0 C
3
~
-
+
DELETE
SET UP F/TC DIAG
LIST CORCT BS TRACK
DUMP LOAD FS
DISP EXIT RETURN
T SET
PLAY
STOP
STILL REW FF
STB OFF
A3 A4
TC REC EDIT
2
4
1
3 MIX
MIX
2
4
1
3 MIX
MIX
2
4
1
3 MIX
MIX
2
SDI
CH 1 CH 2
V2 / V1 PB REC
CH 3 CH 4
INT
ANALOG SDI
10
10
20
30
00
INT
INT
ANALOG SDI INT
ANALOG SDI
V2 INPUT
INT
0
10
10
20
30
00
0
10
10
20
30
00
0
CH 1
POWER
OFF ON
UNI
VAR
CH 2 CH 3 CH 4
ANALOG V1/V2
REC
TOTAL
([SHIFT]+[DUR])
LAST ED
([SHIFT]+[OUT])
LAST X
([SHIFT]+[IN])