Sony TA-VA80ES - Manuel (Page 23)

23 EN
Getting Started Advanced Remote Operations
Operating One Component
While Using Another
(background operation)
You can temporarily operate other components while
listening to or watching a program.
BACKGROUND
2 1 3
LEARN SLEEP VISUAL POWER
SYSTEM OFF
SLOPE BAND
EQ/
TONE
DIGTAL PROCESSING CONTROL
PROGRAMMABLE
— LEVEL —
DIRECT REAR
BASS BOOST
MUTING
CENTER
MASTER
VOL
MODE GENRE — SOUND FIELD — ON/OFF TEST
TONE
TV CONTROL 5.1 INPUT
5 4 6 TV/VIDEO
8 7 9
D.TUNING DISC
0
BACK
GROUND SHIFT ENTER
RMS/START
CH/
PRESET
SYSTEM CONTROL / FUNCTION
VIDEO 3 VIDEO 2 VIDEO 1 LD TV
(AUTO CATEGORIZE SYSTEM)
CD DAT/MD
> 10
TAPE
ON
TUNER PHONO
+ +
– –
+
–
POSITION – SUB CH +
— RMS —
SWAP ANT TV/VTR
= ) 0 + D. SKIP
CLEAR DIRECTION P IN P JUMP
p (
DPC MODE
9 P r
1
Hold down BACKGROUND.
2
Press both the corresponding button of the
component you’re going to use (see the table
below) and one of the following buttons at the
same time; VISUAL POWER, TV/VIDEO, CH/
PRESET +/–, ANT TV/VTR, D.SKIP,
(, 9, p,
0/), =/+, P, r.
Example: To start recording on a tape deck
while listening to a CD
While holding down BACKGROUND,
press 4 (or 5) and press r + ( at the
same time.
The following buttons correspond to the
components.
The button Corresponds to
1 CD player
2 DAT deck
3 MD deck
4 Tape deck A
5 Tape deck B
6 LD player
7 VCR (remote control mode VTR 1
*
)
8 VCR (remote control mode VTR 2
*
)
9 VCR (remote control mode VTR 3
*
)
>10 DBS (Digital Broadcasting System)
tuner
* Sony VCRs are operated with a VTR 1, 2 or 3 setting
that corresponds to Beta, 8mm, and VHS,
respectively.
Changing the Factory Setting
of a FUNCTION Button
If the factory settings of the SYSTEM CONTROL/
FUNCTION buttons (page 12) don’t match your
system components, you can change them. For
example, if you connect a Sony LD player to the
VIDEO 2 jacks, you can assign the VIDEO 2 button to
set the remote to control the LD player.
Note that the settings of the TUNER and PHONO
buttons cannot be changed.
SYSTEM
CONTROL/
FUNCTION
2 1 3
LEARN SLEEP VISUAL POWER
SYSTEM OFF
SLOPE BAND
EQ/
TONE
DIGTAL PROCESSING CONTROL
PROGRAMMABLE
— LEVEL —
DIRECT REAR
BASS BOOST
MUTING
CENTER
MASTER VOL
MODE GENRE
— SOUND FIELD —
ON/OFF
TEST
TONE
TV CONTROL 5.1 INPUT
5 4 6 TV/VIDEO
8 7 9
D.TUNING DISC
0
BACK
GROUND SHIFT ENTER
RMS/START
CH/
PRESET
SYSTEM CONTROL / FUNCTION
VIDEO 3 VIDEO 2 VIDEO 1 LD TV
(AUTO CATEGORIZE SYSTEM)
CD DAT/MD
> 10
TAPE
ON
TUNER PHONO
+ +
– –
+
–
POSITION – SUB CH +
— RMS —
SWAP
ANT
TV/VTR
= ) 0 + D. SKIP
CLEAR DIRECTION P IN P JUMP
p (
DPC MODE
9 P r
1
Hold down the SYSTEM CONTROL/FUNCTION
button whose function you want to change
(VIDEO 2, for example).
2
Press the corresponding numeric button of the
component you want to assign to the SYSTEM
CONTROL/FUNCTION button (6 - LD player,
for example).
For the numeric buttons, see the table in
“Operating One Component While Using
Another” on this page.
Now you can use the VIDEO 2 button to control
your Sony LD player.
To reset the setting to the factory setting
Repeat the above procedure.
Numeric
buttons
Numeric
buttons
Advanced Remote Operations