Setting up the network, Home media gallery 06 – Pioneer PDX-Z9 Manuel d'utilisation

Page 30

Advertising
background image

Home Media Gallery

06

30

En

Setting up the network

In case the router connected to the LAN terminal on
this receiver is a broadband router (with the built-in
DHCP server function), simply turn on the DHCP
server function, and you will not need to set up the
network manually.

You must set up the network as

described below only when you have connected this
receiver to a server without the DHCP server function.
Before you set up the network, consult with your ISP or
the network manager for the required settings. It is
advisory that you also refer to the operation manual
supplied with your network component.

In case you make changes to the network configuration
without the DHCP server function, make the corresponding
changes to the network settings of this receiver.

IP Address

The IP address to be entered must be defined within the
following ranges. If the IP address defined is beyond the
following ranges, you cannot play back audio files stored
on components on the network or listen to Internet radio
stations.
Class A: 10.0.0.1 to 10.255.255.254
Class B: 172.16.0.1 to 172.31.255.254
Class C: 192.168.0.1 to 192.168.255.254

Subnet Mask

In case an xDSL modem or a terminal adapter is directly
connected to this receiver, enter the subnet mask
provided by your ISP on paper. In most of the cases, enter
255.255.255.0.

Gateway IP

In case a gateway (router) is connected to this receiver,
enter the corresponding IP address.

DNS Server Preferred/DNS Server Alternate

In case there is only one DNS server address provided by
your ISP on paper, enter

‘DNS Server Preferred’

. In case

there are more than two DNS server addresses, enter

‘DNS Server Alternate’

in the other DNS server address

field.

Proxy Hostname/Proxy Port

This setting is required when you connect this receiver to
the Internet via a proxy server. Enter the IP address of
your proxy server in the

‘Proxy Hostname’

field. Also,

enter the port number of your proxy server in the

‘Proxy

Port’

field.

Tip

• To delete alphanumeric characters entered one at a

time, press

CLEAR

.

• To return to the immediately previous setting menu,

press

RETURN

. When

‘Cancel Key Editing Lose

Changes?’

is display, press

to return to the

previous setting menu (the previously set menu
contents will be canceled). Press

to return to the

current setting menu.

• It may prove convenient to make a note of the

addresses input in each step.

1

Press HOME MEDIA GALLERY.

It may take several seconds for this receiver to access the
network.

2

Use

/

to select ‘SETUP’ then press

.

3

Use

/

to select ‘Network Setup’ then press

ENTER.

The

‘Network Connection’

screen appears.

4

Either ‘Network Found’ or ‘No Network Found’

appears. Check the network connection status and
press

.

Network Found

– Connected to a component on the

network.

No Network Found

– Not connected to a

component on the network.

The

‘Network IP Settings’

screen appears.

Yes

No

1. Connect this unit to the
local area network (LAN)
(see page 21).

Q: Is the connected
router equipped with
DHCP server operation?

Set the router’s DHCP server
function to ON (no settings
required on this receiver).

2. Make network settings.

Consult the instructions below
and set the receiver as required.

S e t u

p

F a v o r i t e s

WMP 1 1

4

4

S e t u

p

N e t wo r k S e t u

p

I n f o r ma t i o n

N e t wo r k Co n n e c t i o n

N e t wo r k F o u n d

PDX-Z9.book 30 ページ 2008年2月26日 火曜日 午後6時32分

Advertising