JVC RX-DP15BC - Manuel (Page 83)

80
English
To use the stored signals
When you want to use the stored signals, follow the procedure
below.
1. Set the LEARN/TRANSMIT (ZONE 1/ZONE 2)
selector to “TRANSMIT (ZONE 1/ZONE 2).”
2. Press one of the source selecting buttons (or
CONTROL repeatedly) to select the desired
remote control operation mode (source).
3. Press the desired button.
Notes:
• To operate the TV, CATV tuner, or DBS tuner, set the TV operation
mode selector correctly.
• To use the following buttons, you can skip step 2 above.
– TV/CATV/DBS (STANDBY/ON) , VCR 1 (STANDBY/ON) ,
TV VOL +/–, TV/VIDEO, DVD MENU
• To use the following buttons, press DVD MENU first.
– SET, % / fi / @ / #
To erase the stored signals
After erasing the stored signals, preset signals are resumed and you
can operate JVC’s components again.
1. Set the LEARN/TRANSMIT (ZONE 1/
ZONE 2) selector to “LEARN.”
2. Press and hold EXIT, then press one of the source
selecting buttons from which you want to erase
the stored signals.
“CLEAR” appears on the display, and all the signals stored in
the selected remote mode (source) are erased at the same time.
Notes:
• You cannot erase a signal assigned to a particular button only.
Storing a new signal to a particular button erases the previously
stored signal.
• To erase the stored signals for “CD DISC,” first press
CONTROL to select “CD DISC,” then press CONTROL again
while holding EXIT this time.
3. Set the LEARN/TRANSMIT (ZONE 1/ZONE 2)
selector to “TRANSMIT (ZONE 1/ZONE 2)” to
finish the erasing procedure.
IMPORTANT:
To operate the other component(s) using this remote control—
• Aim directly at the remote sensor(s) on the target component(s).
– This remote control can send signals at a distance of 7 m.
OR
• You can also use the IR signal transmitter connected to this
receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor(s) on the target component(s).
You can operate the other component(s) through the remote
sensor on this receiver.
When using the remote control:
– Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 1” or
“ZONE 2” properly.
For the Zone 1 operations For the Zone 2 operations
ZONE 2
TRANSMIT LEARN
ZONE 1
DVD DVD MULTI CD
CDR
PHONO
TAPE/MD
EXT 7.1CH
VCR 1 VCR 2
FM/AM VIDEO TV/DBS
ZONE 2
TRANSMIT LEARN
ZONE 1
ZONE 2
TRANSMIT LEARN
ZONE 1
DVD DVD MULTI CD
CDR
PHONO
TAPE/MD
EXT 7.1CH
VCR 1 VCR 2
FM/AM VIDEO TV/DBS
and
EXIT
LEARN
\ and
For the Zone 2 operations For the Zone 1 operations
EXIT
ZONE 2
TRANSMIT LEARN
ZONE 1 ZONE 2
TRANSMIT LEARN
ZONE 1
CHANNEL
TV/VIDEO
STANDBY/ON STANDBY/ON
TV/CATV/DBS VCR 1
EFFECT
LIVENESS
FM MODE RETURN 100+
SET
DVD
MENU
1 2 3
4 5 6
7 /P 8 9
10 + 10 0
TV VOL
TUNING
STOP PAUSE
FF/ / REW
REC
PLAY
DOWN UP
68-84_RX-DP15B[C]f.pm6 04.4.14, 3:18 PM 80