JVC RX-DP15BC - Manuel (Page 31)

28
English
To change the source name to “TAPE” or “TV,” repeat the same
procedure above—press and hold TAPE/MD to select “TAPE,” or
press and hold TV/DBS to select “TV” in step 2.
• While selecting “DBS” as the Zone 2 source, you cannot change
the source name to “TV.”
Notes:
• Once you change the source name, it is applied both for the Zone 1
and Zone 2 sources.
• Without changing the source name, you can still use the connected
components. However, there may be some inconvenience:
– “TAPE” or “TV” will appear on the display when you select the MD
recorder or DBS tuner.
– You cannot use the digital input (see page 25) for the MD
recorder.
– You cannot use the COMPU LINK or TEXT COMPU LINK remote
control system (see pages 61 and 63) to operate the MD
recorder.
Using the Sleep Timer
Using the Sleep Timer, you can fall asleep while listening to music.
When the shut-off time comes, the receiver turns off automatically.
• Sleep Timer works for the Zone 1 source only.
From the remote control ONLY:
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and the
shut-off time changes as follows (in minutes):
When the shut-off time comes
The receiver turns off automatically.
• If the Zone 2 source is still playing (the ZONE 2 ON/OFF lamp is
lit) when the shut-off time comes, the receiver will not turn off,
and only the Zone 1 source will shut off.
To check or change the time remaining until the shut-off time
Press SLEEP once.
The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 0min.” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
Recording a Source
For analog-to-analog recording
You can record any analog source through the receiver to—
• the cassette deck (or MD recorder) connected to the TAPE/
MD OUT jacks,
• the VCRs connected to the VCR 1 OUT and VCR 2 OUT
jacks, and
• the CD recorder connected to the CDR OUT jacks
—at the same time.
For digital-to-digital recording
You can record the currently selected digital input source
through the receiver to a digital recording device connected to
the DIGITAL OUT terminal.
Notes:
• Analog-to-digital and digital-to-analog recordings are not
possible.
• No sound adjustments can affect the recording.
IMPORTANT:
• While recording, do not turn off the receiver or Zone 1 source;
otherwise, recording will stop.
• If the same source is selected both for Zone 1 and
Zone 2, operating the Zone 2 source will affect the recording.
Basic adjustment auto memory
This receiver memorizes sound settings for each Zone 1
source—
• when you turn on the power,
• when you change the source, and
• when you turn on One Touch Operation (see page 44).
When you change the Zone 1 source, the memorized settings for
the newly selected source are automatically recalled.
The following can be stored for each source:
• Analog/digital input mode (see page 25)
• Input Attenuator mode (see page 26)
• Analog Direct (see page 27)
• Parametric Equalizer setting (see page 48)
• Midnight mode (see page 49)
• Surround/THX mode (see page 51)
• DSP mode (see page 58)
Notes:
• If the source is FM or AM, you can assign a different setting for
each band.
• The memorized settings are not applied when a source is
selected for Zone 2.
• If you want to memorize the volume level together with the
above settings, set One Touch Operation to “ON” (see page
44).
SLEEP
20 10 30 40 50 60 70 80 90
(Canceled) 0
L
ANALOG SLEEP
SPEAKERS
VOLUME
1
SUBWFR
R
dB
SLEEP indicator
Ex. When the source is “VIDEO.”
19-32_RX-DP15B[C]f.pm6 04.4.14, 6:34 PM 28