JVC RX-DP15BC - Manuel (Page 79)

76
English
After pressing DVD MENU, these
buttons can be used for the DVD
menu operations.
Note:
Refer also to the manual supplied for your DVD player (and the
instructions supplied for the discs).
5. Try to operate your DVD player by pressing one
of the above buttons.
• DO NOT forget to turn on the DVD player before pressing
one of the above buttons.
If more than one code is listed for your brand of DVD player,
try each one until the correct one is entered.
To change the transmittable signals for
operating another manufacturer’s CD player
1. Press and hold AUDIO (ON).
2. Press CD.
Remote’s display
3. Enter a manufacturer’s code using
buttons 1–9, and 0.
See page 77 to find the code.
4. Release AUDIO (ON).
After pressing CD, you can perform the following operations on
a CD player:
1–9, 0, +10 : Selects the tracks.
PLAY : Starts playing.
REW : Fast-reverses the tracks.
FF : Fast-forwards the tracks.
STOP : Stops playing.
PAUSE : Stops playing temporarily. To release, press
PLAY.
Note:
Refer to the manual supplied for your CD player.
5. Try to operate your CD player by pressing one of
the above buttons.
• DO NOT forget to turn on the CD player before pressing one
of the above buttons.
If more than one code is listed for your brand of CD, try each
one until the correct one is entered.
Manufactures’ codes for TV
Manufacturer Codes
JVC 00*, 13, 74
Akai 01, 02
Blaupunkt 03, 04
Fisher 01, 05
Grundig 03, 06, 07
Hitachi 08, 09, 10, 49, 78
Irradio 02
ITT/Nokia 11, 12
Loewe 06, 15, 16
Magnavox 08, 17, 49
Matsushita 86, 87
Mets 50, 51, 52, 53
Mitsubishi 08, 18, 19, 20
Mivar 21
NEC 83
Nordmende 22, 23
Okano 15
Panasonic 24, 25, 26, 27, 76
Philips 15, 17, 28, 75
Pioneer 85
RCA/Proscan 08, 24, 29, 30, 31, 48
SABA 32, 33, 68, 69, 70
Samsung 06, 08, 16, 34, 35, 49
Sanyo 01, 05, 81
Schneider 02, 15, 36
Sharp 37, 38, 77, 88
Sony 39, 80
Telefunken 40, 41, 42, 69
Thomson 71, 72
Toshiba 37, 43, 44, 79
Zenith 45, 46
*This figure is set to the remote control as the initial JVC code.
To change the transmittable signals for
operating another manufacturer’s DVD player
1. Press and hold AUDIO
(STANDBY).
2. Press DVD.
3. Enter a manufacturer’s code using
buttons 1–9, and 0.
See page 77 to find the code.
4. Release AUDIO (STANDBY).
After pressing DVD (or DVD MULTI only for Zone 1
operation), you can perform the following operations on a DVD
player:
1–9, 0, +10 : Selects the titles or the chapters.
PLAY : Starts playing.
4 : Returns to the beginning of the current (or
previous) chapter.
¢ : Skips to the beginning of the next chapter.
STOP : Stops playing.
PAUSE : Stops playing temporarily. To release, press
PLAY.
EFFECT
LIVENESS
FM MODE RETURN 100+
1 2 3
4 5 6
7 /P 8 9
10 + 10 0
Remote’s display
EFFECT
LIVENESS
FM MODE RETURN 100+
1 2 3
4 5 6
7 /P 8 9
10 + 10 0
SET
DVD
MENU
DVD
STANDBY ON
CD
STANDBY ON
68-84_RX-DP15B[C]f.pm6 04.4.14, 3:17 PM 76