JVC RX-8040B - Manuel (Page 46)

44
English
Activating the Surround Modes
Available Surround modes vary depending on the speaker settings
and the incoming signals. (See pages 46 and 47.)
Activating one of the Surround modes for a source automatically
recalls the memorized settings and adjustments (see pages 32 to
41).
You can also use the buttons on the remote control for the same
functions.
IMPORTANT:
Check the following before or while using the buttons and controls.
For Zone 1 operations:
The ZONE 1 indicator lights up on the unit’s display.
• When using the unit:
– “ZONE2” is not shown in the unit’s main display.
• When using the remote control:
– Set the ZONE 1/ZONE 2 selector to ZONE 1.
– Check the indication shown on the remote’s display when you
press a button—this indicates the remote control operation mode
together with multi-room operation mode (either for ZONE 1 or
ZONE 2) for about two hours.
Ex. When you press SURROUND with ZONE 1/ZONE 2 selector
set to ZONE 1.
ZONE 2 ZONE 1
ON/OFF ON/OFF
AUDIO POWER
TV/CATV/DBS DVD
ZONE 2 ZONE 1
ZONE 2 ZONE 1
POWER POWER
STANDBY ON
ZONE 1
Activating the Surround modes
1. Select and play any source excluding
DVD MULTI.
• Make sure you have selected the analog or digital input mode
correctly.
• Surround modes are not valid for DVD MULTI playback
mode.
LINEAR PCM L
SUBWFR
R
ANALOG
VOLUME
PRO LOGIC
SPEAKERS 1
(CINEMA)
NEO:6CINMA NEO:6MUSIC
PL IIx MOVIE* PL IIx MUSIC* PRO LOGIC
ZONE 1
LINEAR PCM
DIGITAL
L
SUBWFR
DUAL DIGITAL AUTO
VOLUME
SPEAKERS 1
ZONE 1
2. Press SURROUND to activate the Surround
mode.
• For multi-channel digital software, incoming signals are
automatically detected and the appropriate Surround mode is
activated (see pages 46 and 47 for details).
– Surround mode automatically activated also varies with the
EX/ES/PLIIx setting.
• For analog sources and digital 2-channel software, you can
select one of the following Surround modes. Each time you
press SURROUND, the Surround modes change as follows:
* In the following cases, “PLII MOVIE” or “PLII MUSIC” is applied:
• When the surround back speakers are set to “NONE.”
• When EX/ES/PLIIx setting is set to “EX/ES OFF.”
• When the Zone 2 speakers are activated.
• For Dual Mono software, you can select the channel you
listen to. (See page 36.)
To adjust the speaker output level, see pages 40 and 41.
Note:
When the Zone 2 speakers are activated or the surround speakers
are set to “NONE,” the 3D-PHONIC processing is applied to the
Surround modes (the 3D-PHONIC indicator also lights up).
To cancel the Surround modes
Press SURROUND/DSP OFF (or SURR/DSP OFF on the remote
control). DVD CD
CDR
PHONO
TAPE/MD
AM
SURR / DSP SURROUND
OFF
VCR 1 VCR 2
FM VIDEO TV/DBS
Ex. When “DOLBY D” is activated.
LINEAR PCM
DIGITAL
L
SUBWFR
LS RS
C R
LFE
DIGITAL AUTO
VOLUME
SPEAKERS 1
ZONE 1
LINEAR PCM L
SUBWFR
R
ANALOG
VOLUME
SPEAKERS 1
ZONE 1
42-50_8040[C].p65 04.5.14, 11:29 44