JVC RX-8040B - Manuel (Page 21)

19
English
Zone 1 (Main Room) Operations
This section explains only the operations commonly used when you play any sound source in Zone 1 (main room).
See pages 26 to 29 for the Zone 2 (sub-room) operations.
•
Before performing Zone 1 operations, it is recommended to finish the basic settings on pages 32 to 38.
IMPORTANT:
Check the following before or while using the buttons and controls.
For Zone 1 operations:
The ZONE 1 indicator lights up on the unit’s display.
• When using the unit:
– “ZONE2” is not shown in the unit’s main display.
• When using the remote control:
– Set the ZONE 1/ZONE 2 selector to ZONE 1.
– Check the indication shown on the remote’s display when you
press a button—this indicates the remote control operation mode
together with multi-room operation mode (either for ZONE 1 or
ZONE 2) for about two hours.
Ex. When you press DVD with ZONE 1/ZONE 2 selector set
to ZONE 1.
Turning the Power On and Off (Standby)
On the front panel:
To turn on the power, press STANDBY/ON.
The STANDBY lamp goes off, and the ZONE 1 indicator lights up
on the display.
The currently selected SPEAKERS 1 and/or 2 indicator(s) also
light(s) up on the display.
• If neither the SPEAKERS 1 nor 2 indicator is lit on the display,
see “Activating the Zone 1 Front Speakers” on page 21.
To turn off the power (into standby mode),
press
STANDBY/ON again.
The STANDBY lamp lights up.
On the remote control:
To turn on the power, press AUDIO POWER ON.
The STANDBY lamp goes off, and the ZONE 1 indicator lights up
on the unit’s display.
The currently selected SPEAKERS 1 and/or 2 indicator(s) also
light(s) up on the unit’s display.
• If neither the SPEAKERS 1 nor 2 indicator is lit, see “Activating
the Zone 1 Front Speakers” on page 21.
To turn off the power (into standby mode),
press AUDIO POWER STANDBY.
The STANDBY lamp lights up.
Notes:
• A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
• If you have turned off the receiver with the volume level set at more
than level “30,” the volume level will be automatically set at level
“30” next time you turn on the receiver.
• Before you turn off the receiver in Zone 1, make sure that no one is
listening to any source in Zone 2 (the ZONE 2 indicator is lit on the
display) since the Zone 2 sound will also be turned off
unexpectedly.
Canceling the Zone 1 Operations
To stop Zone 1 operations and sounds from the Zone 1 speakers,
press ZONE 1 ON/OFF on the unit or the remote control so that the
ZONE 1 indicator goes off from the display.
The currently selected front speakers indicator(s) also go(es) off
from the display (no sound will be heard in Zone 1).
To use this receiver for Zone 1 operations again, press
ZONE 1 ON/OFF again (the ZONE 1 indicator lights up).
The front speakers indicator(s) previously selected light(s) up.
Now the buttons and controls on the unit work for Zone 1
operations.
Note:
If “TURN ON ZONE1 OR ZONE2” appears on the display, press
ZONE 1 ON/OFF or ZONE 2 ON/OFF to listen to the sound in Zone 1
or in Zone 2; Otherwise, the receiver will turn off after about 1 minute.
ON/OFF ON/OFF
AUDIO POWER
TV/CATV/DBS DVD
ZONE 2 ZONE 1
ZONE 2 ZONE 1
POWER POWER
STANDBY ON
ZONE 1
ZONE 2 ZONE 1
The last Zone 1 source appears.
The last Surround/DSP mode
appears. The volume
level appears.
LINEAR PCM L R
ANALOG
VOLUME
SPEAKERS 1
ZONE 1
The ZONE 1 indicator lights up.
ZONE 2 ZONE 1
AUDIO POWER
ZONE 2 ZONE 1 STANDBY ON
ZONE 1
16-29_8040[C].p65 04.5.14, 11:29 19