BE Pressure supply 175,000 BTU Kerosene/Diesel Forced Air Heaters HK175FW - Manuel (Page 6)

6
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE OR WHILE
CONNECTED TO A FUEL SOURCE.
Assembly (continued)
MODELS HK070F ONLY
- Tools required: Medium phillips screw driver.
ASSEMBLING HANDLE
1. Align the holes in the upper housing with the 2 holes in the handle
as shown in Figure 6.
2. Insert and tighten screws securely with screw driver.
ASSEMBLING CORD WRAP
1. Align holes in cord wrap with corresponding holes in rear
handle. Insert screws (B) through holes, attach nuts and
tighten (see Figure 7.).
ASSEMBLING CORD WRAP
1. Insert tabs on cord wrap into slots in shell support, lining up the
holes on the cord wrap with those on the side cover.
2. Insert and tighten screws securely with screw driver.
MODELS HK125W/HK175FW ONLY
- Tools required: Medium phillips screw driver, 5/16” open end or
adjustable wrench, needle nose pliers.
ASSEMBLING FRAME AND WHEELS
1. Slide axle through holes in wheel support frame. Slide wheel
bushings and flat washer (A) on to each end of axle.
2. Slide wheels on to each axle, being sure that the valve stem (if
pneumatic) is to the outside (see Figure 7.).
3. Attach wheel nut to threaded axle and tighten.
4. Place heater on the assembled frame, making sure that the air in-
let end is by the wheels, and the mounting holes on the tank flange
of the heater align with holes in frame.
5. Take the front handle and align the mounting holes with the cor-
responding holes in the tank flange/wheel frame. Slide a screw (A)
through the holes and loosely attach a nut. Repeat for the other 3
holes, then fully tighten all 4 screws and nuts.
6. Repeat this process with the rear handle.
NOTE: The front handle is longer than the rear handle.
MODELS PT-45/70T-KFA ONLY
- Tools required: Medium phillips screw driver.
ASSEMBLING HANDLE
1.Align the holes in the upper housing with the 2 holes in the
handle as shown in Figure 6.
2. Insert and tighten screws securely with screw driver.
ASSEMBLING CORDWRAP
1. Insert tabs on cordwrap into slots in shell support, lining up the
holes on the cordwrap with those on the side cover.
2. Insert and tighten screws securely with screw driver.
MODELS PT-125T/175T/215T-KFA ONLY
- Tools required: Medium phillips screw driver, 5/16” open end
or adjustable wrench, needle nose pliers.
ASSEMBLING FRAME AND WHEELS
1. Slide axle through holes in wheel support frame. Slide wheel
bushings and flat washer (A) on to each end of axle.
2. Slide wheels on to each axle, being sure that the valve stem (if
pneumatic) is to the outside ( see Figure 7.).
3. Attach wheel nut to threaded axle and tighten.
4. Place heater on the assembled frame, making sure that the air
inlet end is by the wheels, and the mounting holes on the tank
flange of the heater align with holes in frame.
5. Take the front handle and align the mounting holes with the
corresponding holes in the tank flange/wheel frame. Slide a
screw (A) through the holes and loosely attach a nut. Repeat
for the other 3 holes, then fully tighten all 4 screws and nuts.
6. Repeat this process with the rear handle .
NOTE: The front handle is longer than the rear handle.
ASSEMBLING CORDWRAP
1. Align holes in cordwrap with corresponding holes in rear
handle. Insert screws (B) through holes, attach nuts and
tighten (see Figure 7.).
Do not operate heater without support
frame fully assembled to tank.
NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING OR WHILE CONNECTED
TO A POWER SOURCE
© 2012, Pinnacle Products International, Inc. 6 Kerosene User’s Manual
Handle Screw
Assembly (Continued)
Figure 6: Attaching Handle for models PT-45 /
70T-KFA
Figure 7 Attaching Handle for models PT-125T /
175T / 215T-KFA
CAUTION
Figure 6: Attaching Handle for model HK070F
Figure 7: Attaching Handle for models HK125W/HK175FW
MODELS PT-45/70T-KFA ONLY
- Tools required: Medium phillips screw driver.
ASSEMBLING HANDLE
1.Align the holes in the upper housing with the 2 holes in the
handle as shown in Figure 6.
2. Insert and tighten screws securely with screw driver.
ASSEMBLING CORDWRAP
1. Insert tabs on cordwrap into slots in shell support, lining up the
holes on the cordwrap with those on the side cover.
2. Insert and tighten screws securely with screw driver.
MODELS PT-125T/175T/215T-KFA ONLY
- Tools required: Medium phillips screw driver, 5/16” open end
or adjustable wrench, needle nose pliers.
ASSEMBLING FRAME AND WHEELS
1. Slide axle through holes in wheel support frame. Slide wheel
bushings and flat washer (A) on to each end of axle.
2. Slide wheels on to each axle, being sure that the valve stem (if
pneumatic) is to the outside ( see Figure 7.).
3. Attach wheel nut to threaded axle and tighten.
4. Place heater on the assembled frame, making sure that the air
inlet end is by the wheels, and the mounting holes on the tank
flange of the heater align with holes in frame.
5. Take the front handle and align the mounting holes with the
corresponding holes in the tank flange/wheel frame. Slide a
screw (A) through the holes and loosely attach a nut. Repeat
for the other 3 holes, then fully tighten all 4 screws and nuts.
6. Repeat this process with the rear handle .
NOTE: The front handle is longer than the rear handle.
ASSEMBLING CORDWRAP
1. Align holes in cordwrap with corresponding holes in rear
handle. Insert screws (B) through holes, attach nuts and
tighten (see Figure 7.).
Do not operate heater without support
frame fully assembled to tank.
NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING OR WHILE CONNECTED
TO A POWER SOURCE
© 2012, Pinnacle Products International, Inc. 6 Kerosene User’s Manual
Handle Screw
Assembly (Continued)
Figure 6: Attaching Handle for models PT-45 /
70T-KFA
Figure 7 Attaching Handle for models PT-125T /
175T / 215T-KFA
CAUTION Do not operate heater without support
frame fully assembled to tank.
CAUTION
Model #s: PT-16-TTC (Single Burner),
PT-32-TTC (Double Burner),
PT-47-TTC (Triple Burner)
User’s Manual and
Operating Instructions
Propane
Tank Top Heaters
IMPORTANT:
Read and understand all of the direc-
tions in this manual before assembling, starting or servic-
ing the heater. Improper use of this heater can cause
serious injury. Keep this manual for future reference.
CONSUMER: Retain this manual for future reference.
Pinnacle Products International, Inc. 668 Stony Hill Road #302 Yardley, PA 19067 USA
Phone: 215-891-8460 Fax: 215-891-8461 Web: www.pinnacleint.com Email: [email protected]
Table of Contents
Safety Information.........................................................2-3
Product Identification........................................................3
Propane Supply................................................................3
Ventilation............................................................3
Assembly..........................................................................3
Connecting Heater to Cylinder..........................................4
Lighting Instructions..........................................................5
Maintenance and Storage.................................................6
Replacement Parts List.....................................................6
Exploded Parts Drawing...................................................7
Warranty...........................................................................8
201000016-12
Carbon Monoxide Hazard This heater produces carbon monoxide, which has no odor. Burning the
heater in an enclosed space can kill you. Never use the heater in enclosed spaces such as a tent, a
camper, any vehicle or recreational vehicle (RV), enclosed shelter, or any other enclosed areas.
Not for use in residential living areas or in non-adequately ventilated enclosed spaces. Never
bring or store a propane cylinder indoors.
WARNING
DANGER
OUTDOOR USE ONLY
S I G E N D
C E
D
R I E T I F
CERTIFIED
FAILURE TO COMPLY WITH THE
PRECAUTIONS AND INSTRUCTIONS
PROVIDED WITH THIS HEATER, CAN
RESULT IN DEATH, SERIOUS BODILY
INJURY AND PROPERTY LOSS, OR
DAMAGE FROM THE HAZARDS OF FIRE,
EXPLOSION, BURN. ASPHYXIATION,
CARBON MONOXIDE POISONING AND / OR
ELECTRIC SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND
AND FOLLOW THE INSTRUCTIONS
SHOULD USE OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER
INFORMATION SUCH AS AN INSTRUCTION
MANUAL, LABELS, ETCETERA, CONTACT
THE MANUFACTURER.