Weston Pro Advantage Vacuum Sealer - Manuel (Page 16)

REPLACING THE SEAL BAR TAPE:
1. Press the ON/OFF Button on the
Control Panel to turn the Vacuum Sealer
“OFF”.
2. Disconnect the Vacuum Sealer from the
power supply.
3. Make sure the Vacuum Sealer is
completely cool.
4. Pick at either end of the Seal Bar
Tape covering the Seal Bar Heating
Element until it lifts slightly (Figure 18).
Grasp the loose end and slowly pull
the Seal Bar Tape back over itself until fully
removed.
5. Remove the backing from a new strip of Seal Bar Tape. Be careful not to allow the
Seal Bar Tape to contact anything including itself while the adhesive side is exposed.
6. Hold one end of the
Seal Bar Tape in each hand. Stick the left end of the Seal Bar
Tape to the flat area on the Base just left of the Seal Bar Heating Element. Apply the
Seal Bar Tape from left to right over the Seal Bar Heating Element. Make sure there
are no wrinkles or folds in the Seal Bar Tape once applied. The Seal Bar Tape should
fully cover the Seal Bar Heating Element.
Figure 18
Seal Bar Tape
Seal Bar Heating
Element
6. Remove the Plastic Lid Base, 2
Release Buttons and the 2 Release
Springs from the Stainless Steel Lid.
7. To install the new
Lid Assembly, turn
the Plastic Lid Base upside down with the
Vacuum Chamber Lid Seal positioned
towards the front of the Vacuum Sealer
and the Seal Bar Insulator facing you.
8. Place the 2 Release Buttons into the
slots (Figure 20). Insert the 2 Release
Springs into the backs of the Release
Buttons.
9. With the
Vacuum Chamber Lid
Seal positioned towards the front of
the Vacuum Sealer and the Seal Bar
Insulator facing you, carefully position
the Plastic Lid Base Assembly back
onto the Stainless Steel Lid so that the
4 screw holes in the Plastic Lid Base
line up with the 4 screw posts on the
Stainless Steel Lid.
10. Use one hand to hold the
Plastic Lid Base and the other to insert and turn the 4 Lid
Screws. HINT: It may work better to tilt the Vacuum Sealer on its side when installing
the Lid Screws.
11.When all 4 Lid Screws are installed, the Plastic Lid Base should be flush to the
Stainless Steel Lid. If it is not, then the Lid Screws may be improperly installed (i.e.
crooked or not tight enough).
Release Button
Figure 20
Release Spring
Plastic Lid Base
Stainless Steel Lid
Seal Bar Insulator
Screw
Posts
de l’aspiration/ du scellage (rampe VACUUM PROGRESS).
Appuyer sur la touche ON/OFF pour interrompre au besoin le processus.
9. NE PAS tenter d’ouvrir le couvercle avant la fin de l’aspiration (risque
d’endommagement de l’appareil). Enfoncer les deux boutons déclencheurs du couvercle
(Figure 7) de chaque côté de la scelleuse pour libérer le verrou, puis ouvrir le couvercle.
10. Retirer le sac à vide scellé. Patienter au moins 20 secondes avant un autre scellage
pour que l’appareil ne surchauffe pas.
11. Appuyer sur la touche ON/OFF (Figure 6) du tableau de commande pour éteindre la
scelleuse.
12. Débrancher la scelleuse de la source d’alimentation avant de quitter les lieux lorsque
le travail est terminé.
REMARQUE: La scelleuse sous vide doit être utilisée UNIQUEMENT avec des SACS SOUS
VIDE. Pour obtenir les meilleurs résultats, utiliser uniquement les sacs sous vide recommandés.
NE PAS UTILISER DES SACS À USAGE DOMESTIQUE ! Toute utilisation contre-indiquée de
cette scelleuse sous vide risque d’endommager l’appareil et pourrait annuler la garantie !
-16- -29-