Sony CMT-MD1 - Manuel (Page 53)

53
Additional Information
Additional Information
Precautions
The nameplate is located on the bottom exterior.
On operating voltage
Before operating the system, check that the
operating voltage of your system is identical with
the voltage of your local power supply.
On safety
• The glass over the display window on the cover of
the CMT-MD1/MD1DX is made of tempered
glass.
Under normal conditions, this tempered glass is
more shock resistant and able to bear more weight
than ordinary glass. This glass, however, may
shatter if it receives a sharp blow or if it is
scratched.
• The system is not disconnected from the AC
power source (mains) as long as it is connected to
the wall outlet, even if the system itself has been
turned off.
• Unplug the system from the wall outlet if it is not
to be used for an extended period of time.
To disconnect the power cord, pull it out by the
plug. Never pull the cord itself.
• Should any solid object or liquid fall into the
system, unplug the system and have it checked by
qualified personnel before operating it any
further.
• AC power cord must be changed only at the
qualified service shop.
• When you connect the power cord to mains, even
through the power is off, the system begins
charging for remote and timer functions.
Therefore the surface of this unit become warm,
this is normal.
On placement
• Make sure the system fan is on during use.
Place the system in a location with adequate air
circulation, and do not place any on the system.
• Place the system in a location with adequate
ventilation to prevent heat build up.
• Do not install the system in a confined space, such
as a bookcase or built-in cabinet to prevent heat
build up.
• Do not place the system in an inclined position.
• Do not place the system in locations where it is;
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight.
On installing
When you move the system, remove the CD or MD.
On operation
• If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player or the MD deck. Should this occur, the
system will not operate properly. Remove the CD
or MD and leave the system turned on for about
an hour until the moisture evaporates.
• When you move the system, take out any discs.
If you have any questions or problems concerning
your system, please consult your nearest Sony
dealer.
On the speaker system
This speaker system is not magnetically shielded
and the picture on TV sets may becomes
magnetically distorted. In such a case, turn off the
power of the TV set once, and after 15 to 30 minutes
turn it on again.
If there seems to be no improvement, locate the
speaker system further away from the TV set. Also,
be sure not to place objects in which magnets are
attached or used near the TV set, such as audio
racks, TV stands and toys. These may cause
magnetic distortion to the picture due to their
interaction with the system.
Notes on MDs
• Do not open the shutter to expose the MD. Close
the shutter immediately if the shutter opens.
• Affix the label supplied with the disc only to the
specified label indentation. Do not affix the label
around the shutter or in other locations. Note that
the shape of the indentation depends on the disc.
• Wipe the disc cartridge with a dry cloth to remove
dirt.
• Do not expose the MD to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
Notes on CDs
• Before playing, clean the CD with a cleaning cloth.
Wipe the CD from the center out.
• Do not use a CD with tape, seals, or paste on it as
this may damage the system.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic
spray intended for vinyl LPs.
• Do not expose the CD to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
Cleaning the cabinet
Use a soft cloth slightly moistened with mild
detergent solution.
Shutter
Label
position