Warning – Superior SLBV 35/40 Manuel d'utilisation

Page 12

Advertising
background image

12

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

SUPERIOR

®

B-VENT GAS FIREPLACES • MODELS SLBV-35, SLBV-40 • CARE AND OPERATION INSTRUCTIONS

WARNING

DO NOT attempt to install

the logs until the appliance

installation has been

completed, the gas line

connected and tested for leaks

and the initial burner operation

has been checked out.

The size and position of the log

set was engineered to give the

appliance a safe, reliable and

attractive flame pattern. Any

attempt to use a different log

set in the fireplace will void

the warranty and will result

in incomplete combustion,

sooting, and poor flame

quality.

Logs get very hot and will

remain hot up to one hour

after gas supply is turned off.

Handle only when logs are

cool. Turn off all electricity

to the appliance before you

install grate, volcanic stone,

embers, and logs.

This appliance is not designed

to burn wood. Any attempt to

do so could cause irreparable

damage to the appliance and

prove hazardous to your safety.

If logs are not installed

according to the log

installation instructions, flame

impingement and improper

combustion could occur and

result in soot and/or excessive

production of carbon monoxide

(CO), a colorless, odorless,

toxic gas.

4. Place the glowing ember material

(rockwool).

Note: The bag of Glowing Embers

contains enough rockwool for several

applications; therefore, do not use the

entire bag at one time. For best glow-

ing effect, replace the ember material

annually.

Refer to Figure 8. Separate the glowing

ember material into pieces about the size

of a quarter. Keep the pieces fluffed up,

not matted. Distribute the pieces over the

surface of the burner, as shown in Figures 9

and 10. Do not use more than is necessary.

Position the embers on the small holes of

the ember bed area.

Note: Make sure the glowing ember

material does NOT cover the main

burner slots.

Bag of Glowing

Embers (Rockwool)

Separate into individual

“Quarter-sized” pieces.

Figure 8

INSTALLING VOLCANIC

STONE, GLOWING EMBERS

(ROCKWOOL), AND LOGS

NOTE: Turn OFF all electricity to the fire-

place before installing volcanic stone,

glowing embers, or logs.

1. Remove the front glass enclosure panel

(see “Removing and Installing the Glass

Enclosure Panel,” on previous Page).

2. Install ceramic brickaded panel liners.

3. Install decorative volcanic stone. Refer to

Figure 7. Sprinkle the decorative volcanic

stone in a pleasing pattern directly on the fire-

box bottom, along the slope and to the back,

at the right and left sides of the burner.

Figure 7

Volcanic Stone

Place Volcanic

Stone As Shown

5. Install the Logs.

The logs have locating notches or slots to

help ensure that they are properly positioned.

The top logs that rest on lower logs, do so

over notches, indents or nubs. Proper log

placement is critical to prevent sooting.

Logs should be placed in the gaps between

the flame peaks and should be positioned so

they do not impinge the flames. Follow the

log placement instructions exactly.

SLBV-35

Carefully position the ceramic fiber logs over

the burner in the order shown in Figure 9

and per the following instructions:

1. Place the left front log (1) as shown. Posi-

tion it on the two left front log brackets.

2. Place the right front log (2) as shown. Po-

sition it on the two right front log brackets.

3. Place the left rear log (3) as shown. Posi-

tion it on the upper and lower left rear log

brackets.

4. Place the right rear log (4) as shown. Posi-

tion it on the right rear log bracket. Note that

the hole on the bottom of the right rear log

rests over the “nub” on the right front log.

SLBV-40

Carefully position the ceramic fiber logs over

the burner in the order shown in Figure 10

and per the following instructions:

1. Place the ember chunk (1) over the tab on

the rear log support as shown.

2. Place the left front log (2) as shown. Posi-

tion it on the two left front log brackets.

3. Place the right front log (3) as shown. Po-

sition it on the two right front log brackets.

4. Place the left rear log (4) as shown. Posi-

tion it on the left rear log bracket.

5. Place the right rear log (5) as shown. Posi-

tion it on the right rear log bracket. Note that

the hole on the bottom of the right rear log

rests over the “Nub” on the right front log.

Advertising