Onkyo HT-R980 - Manuel (Page 23)

23
En
Note
*1 If Direct listening mode is selected, “Dynamic EQ” and
“Dynamic Volume” cannot be selected.
*2 Only when you have selected “Custom” in the “Picture
Mode” (
➔ 46), pressing ENTER allows you to adjust the fol-
lowing items; “Brightness”, “Contrast”, “Hue”, and “Satu-
ration”. Press RETURN to return to the original Video menu.
*3 Depending on the input source and listening mode, not all
channels shown here output the sound.
*4 When you have entered a custom name in “Name Edit”
(
➔ 45), the input source is displayed with that name. But
even if not, the component name may be displayed if the AV
receiver receives it via HDMI connection (
➔ 15).
*5 For the PORT input selector, the name of Universal Port
Option Dock will be displayed.
When you connect an -capable Onkyo component, you
must configure the input display so that can work
properly.
This setting can be done only from the front panel.
Note
• DOCK can be selected for the TV/CD, GAME or VCR/DVR
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time ( ➔ 60).
Note
• Always turn down the volume before connecting your head-
phones.
• While the headphones plug is inserted in the PHONES jack, the
speakers are turned off. (The Powered Zone 2 speakers are not
turned off.)
• When you connect a pair of headphones, the listening mode is
set to Stereo, unless it’s already set to Stereo, Mono or Direct.
• Only the Stereo, Direct and Mono listening modes can be used
with headphones.
With the supplied calibrated microphone, Audyssey 2EQ
automatically determines the number of speakers con-
nected, their size for purposes of bass management, opti-
mum crossover frequencies to the subwoofer (if present),
and distances from the primary listening position.
Audyssey 2EQ then removes the distortion caused by
room acoustics by capturing room acoustical problems
over the listening area in both the frequency and time
domain. The result is clear, well-balanced sound for every-
one. Enabling Audyssey 2EQ allows you to also use
Audyssey Dynamic EQ
® , which maintains the proper
octave-to-octave balance at any volume level ( ➔ 43).
Before using this function, connect and position all of
your speakers.
If “Dynamic EQ” is set to “On” (
➔ 43), the “Equalizer”
setting will be set to “Audyssey” ( ➔ 40). On the other
hand, if it is set to “Off”, the “Dynamic Volume” setting
will be set to “Off” (
➔ 44).
It takes about 15 minutes to complete Audyssey 2EQ
Room Correction and Speaker Setup for 3 positions. Total
measurement time varies depending on the number of
speakers.
Changing the Input Display
1
Press TV/CD, GAME or VCR/DVR so that “TV/
CD”, “GAME” or “VCR/DVR” appears on the
display.
2
Press and hold down TV/CD, GAME or VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select “MD”, “CDR”, “DOCK”
or “TAPE”.
For the TV/CD input selector, the input display
changes in this order:
For the GAME input selector, the setting changes in
this order:
For the VCR/DVR input selector, the setting
changes in this order:
TV/CD
→
MD
→
CDR
DOCK
→
→
TAPE
→
GAME
↔ DOCK
VCR/DVR
↔ DOCK
Using Headphones
Connect a pair of stereo headphones with a stan-
dard plug (1/4 inch or 6.3 mm) to the
PHONES
jack.
Audyssey 2EQ ® Room Correction and
Speaker Setup