Denon DN-S3500 - Manuel (Page 17)

11
ENGLISH
ENGLISH
Adjust sound level
The Sampler playback sound level can be adjusted.
!3 Push the PITCH/VOL. button again when the pitch
input mode, the sound level input mode is set,
PARAMETERS LED flashes and the current
settings are displayed on the character display.
• Start Sampler playback.
!4 Turning the PARAMETERS knob can change the
output sound level.
!5 Push the PITCH/VOL. button again to turn the
sound level input mode off.
Adjust pitch
The Sampler playback pitch can be adjusted.
!1 Push the PITCH/VOL. button, the pitch input mode
is set, PARAMETERS LED flashes and the current
settings are displayed on the character display.
• Start Sampler playback.
!2 Turning the PARAMETERS knob can change the
pitch.
✽ When pushing down and turning the PARAMETERS
knob, you can change the pitch range 10 times
faster.
6
Exit and Reloop
u The EXIT/RELOOP button
can be used same as
Seamless Loop function.
7
Reverse Play
i You can play the Sampled
sound in reverse by pushing
the REV button. In reverse
play mode REV LED lights
up and the platter spins
backwards.
• Reverse playback will take affect when
you push the SAMP button after reverse
mode has been turned on. To return to
normal forward playback, push the REV
button once again.
9
Clearing the Sampler data
!0 During the Sampler stop mode, press the
REV/(CLR) button, while pushing the SAMP
button to clear the Sampler.
• Or, by pushing the REV/(CLR) button for
more than. 1 sec, you can clear Sampler.
8
Moving Sampler B point
o When the B button is
pushed during Sampler
playback, the B point
moves to the point at which
the button was pushed, and
loop playback from point A starts.
RELOOP
EXIT/
CLR
REV.
B
SAMP.
CLR
REV.
B TRIM CLR
T. T T
T
ET
O
REV. V V PITCH/V // OL.
q, r, !0, !6, !7
i, !0
!1, !3, !5, !6
y, u
w, o, !6
e, t, !7
PARAMETER P P S PUSH ON/OFF
RELOOP EXIT/
MODE
FILE SEARCH
B TRIM
A2 B
RELAY A A
CONT. T T
!2, !4
1
Record in Sampler
q When the SAMP button is
pushed in the standby or
play mode, the sound from
SAMP point is recorded to
Sampler memory up to 15
seconds.
• The SAMP button is flashing while
recording and a 15 sec REC countdown
display will appear. When the recording is
completed, the button turns off and the
corresponding SAMP B LED lights up.
• The remain time of the Sampler memory
is displayed in the character display.
4
Play Sampler sound
r Playback of the Sampler
sound starts when the
SAMP button is pushed
after recording has
stopped.
• Sampler playback continues looping.
When setting a B point, playback loops
between A and B point. Without a B point
the Sampler loops the whole recorded
length (about 15 seconds).
t To stop the Sampler sound
push the STOP button.
• Stutter playback of the
sample is possible when
the STOP button is
pushed repeatedly in the STOP mode.
SAMP.
Stop recording
e To stop the sampler
recording, press the STOP
button at any time prior to
15 sec.
• The EXIT/RELOOP LED
light to indicates Sampler Loop mode is
set automatically.
3
SAMP.
STOP
DN-S3500 has one Sampler of 15 seconds in length. This Sampler can also be looped and scratched during playback.
2
Setting B point
w When the B button is
pushed during Sampler
recording, the Sampler
Loop B point is set and the
loop mode turns on.
• Recording continues for approximately 15
seconds without stopping after set B
point.
• If the B point is not set, the recording end
point is set as your B point automatically.
Also EXIT/RELOOP LED light to indicates
Sampler Loop mode is set automatically.
B
Select Sampler Loop mode
You can select 1 of 3 playback modes for
Sampler when the Sampler is not playing.
Loop! (default):
Sampler playback continues with
looping.
(EXIT/RELOOP LED stays lit)
Single All!:
Sampler playback continues over B
point up to recording length.
(EXIT/RELOOP LED flashes)
Single B!:
Sampler playback stops at B point.
(EXIT/RELOOP LED turned off)
y To select loop mode, push
EXIT/RELOOP button after
recording and before playing.
5
RELOOP
EXIT/
STOP
10 SAMPLER
Copy from A1/A2 sound
You can copy A1/A2 Seamless Loop into the Sampler
up to 15 sec.
!6 Copy from A1
• When the B button of the Sampler is pressed,
“SAMP 0 A1” and “Copy/Push Samp” are
displayed.
Then quickly push the SAMP button, the copying
is completed within seconds.
!7 Copy from A2
• When the STOP button is pressed, “SAMP 0
A2” and “Copy/Push Samp” are displayed.
Then quickly push the SAMP button, the copying
is completed within seconds.
NOTES:
• You can not copy when the Sampler is already loaded.
• You can copy just your Hot Start A1/A2 points
(without a B point set) for up to 15 sec in the Cue
mode.