Denon DN-S3500 - Manuel (Page 13)

7
ENGLISH
ENGLISH
Power on play
• When “POWER ON PLAY” is set to “ON” at “⁄5
PRESET (10)”, playback starts from the first track on
the disc when the power is turned on.
Relay playback
• Relay Play function is a useful mode to continue
playback between two DN-S3500s.
• Connect the MEMO IN/OUT terminals between two
DN-S3500s.
1
Start Relay Play
q Push the RELAY
button for more than
1 sec to enable
Relay play mode.
You can set Relay
play mode as below.
• In the single play mode, when the one
player’s playback reaches end of track,
another DN-S3500 starts playing.
• In the continuous play mode, when all
tracks on one player are finished, another
DN-S3500 starts.
• The discs in two DN-S3500s can be
played alternately by setting both DN-
S3500 to the relay play mode.
/SINGLE
RELAY
CONT.
2
Stop Relay Play
w When the RELAY
button is pushed for
more than 1 sec
while in the relay
play mode, the relay
play mode is turned
off. /SINGLE
RELAY
CONT.
PARAMETER P P S
PUSH ON/OFF
RELOOP EXIT/
MODE
FILE SEARCH
B TRIM
A2 B
RE
CONT. T T
q, w
2
0
Move the #3 Pitch Slider to adjust
the pitch. The current pitch setting
is displayed on the display.
Pitch decreases
Pitch increases
3
DN-S3500 has six pitch ranges, 4%, 10%,
16%, 24%, 50% and 100%.
When the
#4 RANGE button
is pushed for more than 1 sec,
the pitch range can be selected
with the
@7 PARAMETERS knob.
• When the @7 PARAMETERS knob is pushed
the pitch range is entered and the pitch range
selection mode is cancelled.
NOTE:
Only a max of 16% range for MP3 discs.
• With PITCH BEND function you can change pitch
temporary. DN-S3500 has two ways for this function
PITCH BEND buttons and Scratch Disc.
Pitch Bend
PITCH
RANGE
TRACK SEARCH
PARAMETERS
PUSH ON/OFF
1
3
PITCH BEND +/– buttons
• Push the
#1 PITCH BEND – or #2 + button for
momentary change of pitch.
While holding these
buttons down, the pitch
continues to change up
to the limitation.
• After releasing the
PITCH BEND buttons,
playback pitch returns to slider setting.
Scratch Disc
• When the Platter source is
set to BEND, the playback
speed can be changed by
turning
!0 Scratch Disc during
playback. The display will
indicate “Pitch Bend” during this mode.
• The pitch increases gradually when the
Scratch Disc is turned clockwise and
decreases when turned counterclockwise.
• When you stop turning the Scratch Disc, the
playing speed returns to the previous pitch.
PITCH BEND
2
When the Platter source is set
to MAIN and the Platter is
turning, playback of the Main
source can be slowed
temporarily by lightly pressing
!0 Scratch Disc or PLATTER.
In addition, playback can be quickened
temporarily by pushing Scratch Disc or
PLATTER in the direction in which the Platter is
turning.
1
Push the #4 PITCH button to
PITCH LED lights up.
PITCH
RANGE
• With the Pitch slider you can adjust the playback
speed (Pitch).
• If you would not prefer to change key of sound, use
the Key Adjust function.
Adjusting the pitch and Key Adjust
4 -1
KEY ADJUST ON
When the
#5 KEY ADJUST button is pushed,
the Key Adjust function is turned on and lights
up “KEY ADJ.” in the display.
4 -2
KEY ADJUST OFF
When the
#5 KEY ADJUST button is pushed
again, the Key Adjust function is turned off.