Panasonic PT-DW100U - Manuel (Page 119)

ENGLISH – 119
Information
Model No. PT-DW100U
Interface
ports
RGB2 input
terminal
1 set of high-density, D-sub 15p (female)
[For YP
B
P
R
input]
Y: 1.0 V [p-p] synchronization signal included, P
B
P
R
: 0.7 V [p-p] 75 Ω
[For RGB input]
0.7 V [p-p] 75 Ω For G-SYNC: 1.0 V [p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity automatically adjusted
VD: TTL, high-impedance, positive/negative polarity automatically adjusted
HD/SYNC, and VD terminals are not compliant with 3-value direct SYNC. •
Video input/
output terminal 1 set BNC
1.0 V [p-p] 75 Ω (Active through for Video output)
S-video input
terminal 1 set Mini DIN 4p
Y 1.0 V [p-p] C 0.286 V [p-p] 75 Ω Compliant with S1 signals
DVI-D input
terminal
1 set
DVI 1.0 compliant
HDCP (Single link only) compatible
LAN terminal
1 set (Used for network connection)
10BASE-T/100BASE-TX
PJLink™ compatible
Serial input
terminal 2 sets D-sub 9-pin (female), RS-232C/RS-422 compliant
Used for personal computer control
Serial output
terminal 1 set D-sub 9-pin (male), RS-422 compliant
Used for personal computer control
Remote1 input/
output terminal 1 set each for M3 pin jack
Wired remote control, used for link control
Remote2 terminal
D-sub 9p (female)
Used for external control
Length of power supply cord 3.0 m (9.1´)
Cabinet Molded resin
Outside dimensions Width: 578 mm (22.8˝), Height : 320 mm (12.6˝), Depth: 643 mm (25.3˝)
Weight approx. 35 k g (77.1 lb) (without optional projection lens) *2
Working environment
condition Ambient temperature *3 : 0 C to 45 C
Ambient humidity: 10 % to 80 % (no condensation)
Remote
control
Power source 3 V DC (two AA dry cells)
Operation range approx. 30 m (98´5˝) (in front of beam receiver)
Mass 134 g (0.31 lb) (including dry cells)
Outside dimensions Width: 51 mm (2˝), Thickness: 23 mm (0.9˝), Depth: 176 mm (6.9˝)
Optional
Hanging attachment (For high ceiling): ET-PKD100H
Hanging attachment (For low ceiling): ET-PKD100S
Projection lens: ET-D75LE1, ET-D75LE2, ET-D75LE3,
ET-D75LE4, ET-D75LE5, ET-D75LE6,
ET-D75LE8
DVI-D input module: ET-MD77DV
SD-SDI input module: ET-MD77SD1
HD/SD-SDI input module: ET-MD77SD3
Dual link HD/SD-SDI input module: ET-MD100SD4
Replacement Lamp Unit: ET-LAD12K (single bulb),
ET-LAD12KF (4 bulbs)
*1 70˝ – 300˝ for ET-D75LE5
*2 This is the average value. It may differ depending on each product.
*3 When the projector is used in high altitude mode (1 400 to 2 700 m), the ambient temperature is 0
C to 40 C .
Furthermore, if the ambient temperature becomes 40 C or more (35 C in high altitude mode) when using the
projector with lamp 4 lit, light output may be reduced by approximately 30% to protect the projector.
When a smoke cut filter is used, the ambient temperature is 0
C to 35 C . However, use at high altitudes is not
possible.