Sony CDX-R3300 Manuel d'utilisation

Fm / am compact disc player, 2a b

Advertising
background image

© 2004 Sony Corporation

Printed in Korea

3-261-846-11

(1)

Cautions

• This unit is designed for negative ground 12 V

DC operation only.

• Do not get the leads under a screw, or caught

in moving parts (e.g. seat railing).

• Before making connections, turn the car

ignition off to avoid short circuits.

• Connect the yellow and red power input leads

only after all other leads have been connected.

Run all ground leads to a common ground

point.

• Be sure to insulate any loose unconnected

leads with electrical tape for safety.

• The use of optical instruments with this

product will increase eye hazard.

Notes on the power supply lead (yellow)
• When connecting this unit in combination with

other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.

• When no car circuits are rated high enough,

connect the unit directly to the battery.

Parts Iist (1)

• The numbers in the list are keyed to those in

the instructions.

• The bracket 1 and the protection collar 3 are

attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar
3

from the unit. For details, see “Removing

the protection collar and the bracket (4)” on
the reverse side of the sheet.

Keep the release keys 5 for future use as

they are also necessary if you remove the
unit from your car.

Caution

Handle the bracket 1 carefully to avoid injuring
your fingers.

Note
Before installing, make sure that the catches on
both sides of the bracket
1 are bent inwards 2 mm
(

3

/

32

in). If the catches are straight or bent outwards,

the unit will not be installed securely and may spring
out.

Installation/Connections

Installation/Connexions

FM/AM
Compact Disc
Player

Connection example (2)

Notes (2-B)
• Be sure to connect the ground lead before

connecting the amplifier.

• If you connect an optional power amplifier and do

not use the built-in amplifier, the beep sound will
be deactivated.

Connection diagram (3)

1

To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.

2

To the power antenna control lead or power
supply lead of antenna booster amplifier

Notes
• It is not necessary to connect this lead if there

is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control
and power supply leads.”

3

To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch

Notes
• If there is no accessory position, connect to the

+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control
and power supply leads.”

5

To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a
metal surface of the car first.

2

A

B

AUDIO OUT REAR

1

3

2

Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)

Rear speaker
Haut-parleur arrière

Front speaker
Haut-parleur avant

1

Power amplifier
Amplificateur de puissance

5

×

2

4

Active subwoofer
Caisson de graves actif

CDX-R3300
CDX-R3000

Catch

1

Ч

4

Advertising
Ce manuel est liée aux produits suivants: