Settings after connections, Signal format] setup, System settings – Pioneer PDP-504CMX-S Manuel d'utilisation

Page 23

Advertising
background image

17

En

System Settings

English

3

Use the

5/ buttons to select [SIGNAL FORMAT],

then press the SET button.

:

V G A

:

:

SIGNAL FORMAT

CLAMP POSITION

:

AUTO

POWER MANAGEMENT

OFF

MENU

INPUT1

PICTURE

SCREEN

SETUP

OPTION

4

Use the

2/3 buttons to select the display mode.

SET

SET

EXIT

MENU

:

SIGNAL FORMAT

VGA

1 When the input signal has a refresh rate of 31.5

kHz horizontal / 60 Hz vertical, pressing

2/3 will

cause the display mode to change alternately as
follows:

2 When the input signal has a refresh rate of 48.4

kHz horizontal / 60 Hz vertical, or 56.1 kHz
horizontal / 70 Hz vertical, pressing

2/3 will cause

the display mode to change alternately as follows:

3 When the input signal has a refresh rate of 64 kHz

horizontal / 60 Hz vertical, 80 kHz horizontal / 75 Hz
vertical, or 91.2 kHz horizontal / 85 Hz vertical,
pressing

2/3 will cause the display mode to

change alternately as follows:

If the [PC AUTO] setting is selected when using the
above PC input signals, screen resolution will
automatically switch between [XGA] and [WXGA].

Notes

÷ The [PC AUTO] setting supports automatic signal selection

only when using RGB separate SYNC inputs.

÷ When G ON SYNC or Composite SYNC signals are input,

selecting [PC AUTO] will cause the screen resolution to be set

to [XGA] only.

÷ When using G ON SYNC or Composite SYNC with WXGA

inputs, set [SIGNAL FORMAT] manually to [WXGA].

5

Press the SET button.
The setting is stored in memory and the screen
returns to that shown in step 3.

6

When the setup is completed, press the MENU
button to exit the menu screen.

Note

Make [SIGNAL FORMAT] setting for each input (INPUT1 and

INPUT2).

Settings after connections

After components have been connected to INPUT1 or
INPUT2, on-screen setup is necessary.
Follow the procedure described below and make settings
as they apply to the type of components connected.

[SIGNAL FORMAT] setup

Note

These settings are required only when using the following input

signal refresh rates: 1 31.5 kHz horizontal / 60 Hz vertical; 2

48.4 kHz horizontal / 60 Hz vertical, or 56.1 kHz horizontal / 70 Hz
vertical; 3 64 kHz horizontal / 60 Hz vertical, 80 kHz horizontal /

75 Hz vertical, or 91.2 kHz horizontal / 85 Hz vertical. No manual

setup is necessary for signals with other refresh rates, since
adjustments are performed automatically (the [SIGNAL FORMAT]

item will not be displayed).

1

Press the MENU button to display the menu
screen.

MENU

INPUT1

ENTER

SET

EXIT

MENU

PICTURE

SCREEN

SETUP

OPTION

:

0

:

0

:

0

:

0

:

0

:

0

CONTRAST

:

0

BRIGHTNESS
R.LEVEL
G.LEVEL
B.LEVEL
H.ENHANCE
V.ENHANCE

PICTURE RESET

2

Use the

2/3 buttons to select [SETUP].

: V G A

:
:

SIGNAL FORMAT

CLAMP POSITION

:

AUTO

POWER MANAGEMENT

OFF

MENU

INPUT1

PICTURE

SCREEN

SETUP

OPTION

System Settings

3 WVGA 2

3 VGA 2

3 PC AUTO 2

3 WXGA 2

3 XGA 2

3 SXGA 2

3 SXGA+ 2

MENU

2/3

5/

SET

MENU

5/

SET

2/3

Main unit operating
panel

Remote control unit

Advertising
Ce manuel est liée aux produits suivants: