Pioneer DJM-2000 - Manuel (Page 7)

DRB1496-D
En 7
English
7
Connections
Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Refer to the operating instructions for the component to be connected.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.
Rear Panel
CH 2 CH 3 CH 4 CH 1 SIGNAL GND
CD
CD
L
R
L
R
PHONO
MIDI OUT USB
CD LINE
CONTROL
OUT IN
(TRS)
R L
R L
R
L
R L(MONO) R L(MONO)
DIGITAL
BOOTH SEND RETURN
COMPUTER 1
COMPUTER 2
LINK
CH 3 CH 1
CH 4 CH 2
CH 2 CH 3 CH 4 CH 1
DIGITAL
SIGNAL GND
CD
1GND
-6dB -3dB 0dB
2HOT
3COLD
CD
L
R
PHONO
POWER
AC IN
OFF
ON
MASTER1
MASTER
ATT.
MASTER2 REC OUT
DIGITAL CD DIGITAL
L
R
CD LINE
CONTROL
CD DIGITAL
1 2 6 3 3 4 5 2 3 4 5 a
b c
7 8 5 6 3 7 5 9
d e f g k h i j l
1 POWER (page 13)
Turns this unit’s power on and off.
2 PHONO (page 8)
Connect to a phono level (MM cartridge) output device. Do not input line level
signals.
3 CD (page 8)
Connect to a DJ player or a line level output component.
4 SIGNAL GND (page 8)
Connect an analog player’s ground wire here. This helps reduce noise when
the analog player is connected.
5 CD, DIGITAL (page 13)
Selects the analog signal input terminals (CD) or the digital signal input
terminals (DIGITAL IN).
6 LINE (page 8)
Connect to a cassette deck or a line level output component.
7 CONTROL (page 8)
Connect using a control cord (included with Pioneer DJ players).
8 DIGITAL OUT (page 8)
Outputs the master channel audio signals.
9 DIGITAL IN (page 8)
Connect these to the digital coaxial output terminals on DJ players, etc. The
sound may be momentarily interrupted when the output signal sampling
frequency is switched.
a Kensington security slot
b USB (page 9)
Connect to a computer.
c MIDI OUT (page 8)
Connect this to the MIDI IN terminal on an external MIDI sequencer.
d LINK (page 8)
Connect these to the LINK terminals on Pioneer DJ players or the LAN ports
of computers on which rekordbox is installed (PRO DJ LINK).
e RETURN (page 8)
Connect to the output terminal of an external effector. When the [L (MONO)]
channel only is connected, the [L (MONO)] channel input is simultaneously
input to the [R] channel.
f SEND (page 8)
Connect to the input terminal of an external effector. When the [L (MONO)]
channel only is connected, a monaural audio signal is output.
g BOOTH (page 8)
Output terminals for a booth monitor, compatible with balanced or unbal-
anced output for a TRS connector.
h REC OUT (page 8)
This is an output terminal for recording.
i MASTER2 (page 8)
Connect to a power amplifier, etc.
j MASTER ATT.
Switches the attenuation level of the sound output from the [MASTER1] and
[MASTER2] terminals. Select 0 dB, –3 dB or –6 dB.
k MASTER1 (page 8)
Connect to a power amplifier, etc.
l AC IN
Connect to a power outlet using the included power cord. Wait until all con-
nections between the equipment are completed before connecting the power
cord.
Be sure to use the included power cord.