Marantz DR4050 - Manuel (Page 26)

• You can program up to 99 tracks to play in any desired
sequence.
• Tracks can be programmed more than once, but each time
counts as a track. ( S ST TE EP P )
• A program for playback can be made from both the disc in
the recorder deck and the disc in the player deck. A program
for recording can only be made from the disc in the player
deck.
Programming for playback
11 Select Changer mode or DJ mode using the DJ MODE key.
➜ CHANGER or DJ MODE appears on the display.
22 Press CDR or CD to select the required deck.
➜ Selected key lights up.
33 Press PROG(ram) to enter Program mode.
➜
P PR RO OG G flashes and PROGRAM followed by track
information appears on the display.
44 Select the required track numbers by turning the EASY
JOG/ENTER key left or right and store by pressing ENTER.
or:
Key in a track number with the number keys on the remote
control and press ENTER to confirm. For 2-digit numbers,
press the keys in rapid succession.
➜ The track will be stored in the program.
➜ The track number, total program time and the number of
programmed tracks ( S ST TE EP P ) are displayed.
55 Repeat step 44 for all tracks to be programmed.
66 Press STOP or PROG(ram) to end programming.
➜
P PR RO OG G lights continuously.
77 Press PLAY/PAUSE 2 ; to start programmed play.
Programming for recording
11 Press REC TYPE to select the required recording mode (see
‘Recording’).
22 Compile your programme as described in “programming for
playback”. (steps 3 to 5)
• Only tracks from the disc in the CD player can be stored.
33 Press REC(ord). to start recording.
Note:
- To review the program, press PROG(ram), followed by 5 or
6 with the CD player or CD recorder in stop mode.
- To add more tracks to the program, repeat steps 11 to 77.
- If you try to store more than 99 tracks,
PROG FULL
appears on the display.
Clearing a program
11 Press STOP 9 if necessary to stop programmed play.
22 Press STOP 9 again to clear the program.
➜
P PR RO OG G disappears from the display.
• The program is also cleared if you open the disc tray.
Erasing a track from a program
11 In Stop mode press PROG(ram) to enter Program mode.
22 Use 5 or 6 to select the track that has to be deleted.
➜ The track number and program step will be shown on
the display.
33 Press CANCEL/DELETE to erase the track from the program.
➜ The remaining program steps and the remaining playing
time of the program will be displayed.
4 Repeat step 2 and 3 for all tracks to be erased.
5 Press STOP 9 or PROG(ram) to end erasing.
➜
P PR RO OG G lights continuosly.
REM TRACK REC TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN I
I
CD
RW
CHANGER
SYNC MANUAL RECORD
REM TOTAL
ALL
TRACK
TIME STEP TRACK
CD
RW
2 7 8 11
REM TRACK REC TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN I
I
CD
RW
CHANGER
SYNC MANUAL RECORD
REM TOTAL
ALL
TRACK
TIME STEP TRACK
CD
RW
1
REM TRACK REC TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN I
I
CD
RW
CHANGER
SYNC MANUAL RECORD
REM TOTAL
ALL
TRACK
TIME STEP TRACK
CD
RW
1 2 3 4 5 6 7 8 9 10 11
Remarks about programming
PROGRAMMING
English
26