GE ZDIS150ZSS - Manuel (Page 5)

Installation Instructions
ADVANCE PLANNING (cont.)
LOCATION REQUIREMENTS:
‡1RWGHVLJQHGIRURXWGRRULQVWDOODWLRQ
‡7KHLFHPDNHUPXVWEHLQVWDOOHGLQDQDUHD
protected from elements such as wind, rain, water
spray or drip. The area should be ven ti lat ed with
temperatures above 55°F (13°C) and below 110°F
(43°C). Best results are obtained between 70°F (21°C)
and 90°F (32°C).
‡7KHLFHPDNHUPD\EHFORVHGLQRQWKHWRSDQG
three sides as long as the front is un ob struct ed
for air circulation and proper op er a tion.
– Installation should be such that the ice maker
can be moved forward for ser vic ing, if necessary.
– The bottom grille on the front must be
unobstructed to provide proper air flow.
WATER SUPPLY
A cold water supply with water pressure of between
30 and 120 psi is required to operate the ice maker.
If you have questions about your water pressure, call
a licensed, qualified plumber.
ELECTRICAL REQUIREMENTS
WARNING :
(Please read carefully).
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED. Do not remove ground
plug. Do not use an adapter. Do not use an
extension cord. Failure to follow these instructions
can result in death, fire or electrical shock.
AVERTISSEMENT :
(S’il vous lisez avec soin). POUR VOTRE SÉCURITÉ,
CET APPAREIL DOIT ÊTRE CORRECTEMENT MIS À
LA TERRE. N’enlevez pas la fiche de mise à la terre.
N’utilisez pas un adaptateur. N’utilisez pas un
cordon de rallonge. L’omission d’observer ces
directives peut entraîner la mort, l’incendie ou
l’électrocution.
Before you move your ice maker into its final
location, it is important to make sure you have the
proper electrical connection:
A 115 volt, 60 Hz., AC only, 15- or 20-amp electrical
supply, properly grounded in accordance with
the National Electrical Code and local codes and
RUGLQDQFHVLVUHTXLUHG8VHDQRXWOHWZKLFKFDQQRW
be turned off by a switch or pull chain.
5
ADVANCE PLANNING (cont.)
IMPORTANT:
This unit must NOT be on a GFCI
(Ground Fault Circuit Interrupter) equipped outlet
or nuisance tripping may occur resulting in loss of
cooling. Ice quality may be affected. If nuisance
tripping has occurred, and if the condition of the ice
appears poor, dispose of the ice.
Recommended Grounding Method
The ice maker must be grounded. The ice maker
is equipped with a power supply cord having a 3
prong grounding plug. The cord must be plugged
into a mating, 3 prong, grounding-type wall outlet,
grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating
wall receptacle is not available, one must be installed
by a qualified electrician.
DRAINING REQUIREMENTS
Determine a method of drainage. If a floor drain
is to be installed, the drain must be accurately
located. The installation of a custom door panel will
affect the drain location. See page 7 to determine the
exact location of the floor drain, front to back, with or
without a custom door panel.
A drain pump kit, ZPK2, is available and will not
interfere with placement of the ice maker.
BEFORE YOU BEGIN:
1. If a custom panel is to be installed, follow the
instructions shown on pages 10 and 11.
–Order ZIP75 (black) panel kit.
– Order the custom panel from the cabinet
manufacturer.
–Secure the custom panel onto the ice maker.
2. The door swing is reversible. If desired, change
the door swing before installation following
instructions on page 13.
3. Slide the ice maker into the installation location.
– Open and close the door to be sure there is no
interference.
– Check to be sure the ice maker can be moved
back into the opening, flush with adjacent
cabinetry. There should be no interference with
the floor drain.
– Check to be sure the ice maker is level. The ice
maker will not operate properly if it is not level.
See page 6.