Denon AVR-1802/882 - Manuel (Page 9)

9
ENGLISH
8 CONNECTIONS
• Do not plug in the power cord until all connections have been
completed.
• Be sure to connect the left and right channels properly (left with
left, right with right).
• Insert the plugs securely. Incomplete connections will result in
the generation of noise.
• Use the AC OUTLETS for audio equipment only. Do not
use them for hair driers, etc.
• Note that binding pin plug cords together with power cords or
placing them near a power transformer will result in generating
hum or other noise.
• Noise or humming may be generated if a connected audio
equipment is used independently without turning the power
of this unit on. If this happens, turn on the power of this unit.
Connecting the audio components
CDR /
TAPE
CDR /
TAPE
DVD /
VDP
TV /
DBS
DVD /
VDP
TV /
DBS
VCR
-1
VCR
-2
VCR
-1
VCR
-2
VCR-1 FRONT
FRONT
PREOUT
CENTER
CENTER
DVD/
VDP
TV/
DBS
VCR-1 VCR-2
S-VIDEO
VCR-1 VCR-2 MONITOR
SUB
WOOFER
SPEAKER SYSTEMS AC OUTLETS
SURROUND AC 120V 60Hz
SWITCHED
TOTAL 120W(1A.)MAX.
PHONO
CD
SIGNAL
GND
MONITOR
VCR-2
VCR-1
VCR-2 OPT-2
OPT-2
OPT-1 FL
AM
ANTENNA TERMINALS
LOOP
ANT.
FM
COAX.
75
SL
EXT. IN AUDIO DIGITAL VIDEO
C
FR
SR
SW
COAX.
SPEAKER IMPEDANCE
FRONT A OR B / 6 16
A + B / 12 16
CENTER / 6 16
SURROUND / 6 16
R
OUTPUT INPUT
L R L
R L
R L R L
R L
R L
L
R
L
R
SUBWOOFER FRONT
LINE OUT LINE IN
CENTER SURROUND LINE OUT
Decoders with 6-channel
analog outputs, etc.
Connecting the AC OUTLETS
AC OUTLETS
• SWITCHED
(total capacity – 120 W (1 A.))
The power to these outlets is turned on and off in conjunction with the POWER switch on the main
unit, and when the power is switched between on and standby from the remote control unit.
No power is supplied from these outlets when this unit’s power is at standby. Never connect
equipment whose total capacity is above 120 W (1 A.)
NOTE:
Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or other
electrical appliances.
AC CORD
AC 120V, 60Hz
Connecting a tape deck
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or REC) to this
unit’s tape recording (OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to
this unit’s tape playback (IN) jacks using pin plug cords.
Tape deck or CD recorder
Connecting a turntable
Connect the turntable’s output cord to this
unit’s PHONO jacks, the L (left) plug to the L
jack, the R (right) plug to the right jack.
NOTE:
This unit cannot be used with MC
cartridges directly. Use a separate head
amplifier or step-up transformer.
If humming or other noise is generated when
the ground wire is connected, disconnect the
ground wire.
Turntable
(MM cartridge)
Ground wire
Use these jacks if you wish to connect external power amplifier(s) to increase the
power of the front and center channels, or for connection to powered loudspeakers.
Connect the internal amplifier’s subwoofer to the subwoofer terminal. (Refer to
page 14.)
Connecting the pre-out jacks
• Analog recording of signals input to the AVR-1802 in digital format is not possible. To record in analog, also connect the analog signals of the
player to the AVR-1802’s analog input terminals.
• The AVR-1802’s OPTICAL OUT terminal is an optical digital output terminal for connection of a CDR recorder, MD recorder or other digital
recording device. Use it for digital recording.