Reverse the door handle, Reinstalling the door – Kenmore ELITE HE4 110.C8586 Manuel d'utilisation

Page 12

Attention! Le texte de ce document a été détectée automatiquement. Pour consulter le document original, vous pouvez utiliser le mode "Original".

Advertising
background image

Reverse the door handle
1.

2

.

Place the outer door assembly face down on work space.

Remove the 2 screws that hold the door handle and the
2 screws holding the hole plugs. If hole plugs do not easily fall
out after screws are removed, insert a small screwdriver Into

the holes and gently push the plugs out.

screw. By putting this screw in first, the door will hang in
place while you insert and tighten the remaining 4 screws.

3. Move the door handle to the other side and reattach with the

2 screws removed from the door handle in Step 2.

4. Move the hole plugs to the new hinge side and attach with

the 2 screws removed from the hole plugs in Step 2.

Reinstalling the door
1.

2

.

Check for fingerprints on the glass. Clean if necessary.

Place the inner door assembly into the outer door assembly.

Align the hinge cover and hinge in the openings on each side.
To fit correctly, the inside door assembly edge is completely

inside the outside door assembly edge.

Reassemble the inner and outer door assemblies with the
6 screws.

4. Use a small flat-blade screwdriver to remove plug strip from

the door opening. Slide the head of the screwdriver under the
top portion of the plug strip, being careful not to scratch the

dryer surface. Lift up. Repeat In the middle and at the bottom.
Remove the plug strip in the door opening and insert in the
opposite side.

5. Insert a screw in the 2nd opening from the top of the hinge

opening and partially tighten. Hang the door by placing the

top hinge keyhole over the 2nd screw head and tighten the

A. Dryer door

B. Dryer

C. Insert this screw first

6. Close the door and check that it latches securely.

1. Check to be sure all parts are now installed. If there is an

extra part, go back through the steps to see which step was
skipped.

2. Check to be sure you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer’s final location. Be sure the vent is not

crushed or kinked.

5. Check to be sure the dryer is level. See “Level Dryer.”

6

.

Plug into a grounded outlet. Turn on power.

7. Remove the blue protective film on the console and any tape

remaining on the dryer.

8

.

Read “Dryer Use.”

9. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

10. Set the dryer on a full heat cycle (not an air cycle) for

20 minutes and start the dryer.

If the dryer will not start, check the following:

■ Controls are set in a running or “On” position.

■ Start button has been pushed firmly,

■ Dryer is plugged into a grounded outlet.

■ Electrical supply is connected.

■ House fuse is intact and tight, or circuit breaker has not

tripped.

■ Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat.

If you do not feel heat, turn off the dryer and check the

following:

■ There may be 2 fuses or circuit breakers for the dryer. Check

to make sure both fuses are intact and tight, or that both
circuit breakers have not tripped. If there is still no heat,
contact a qualified technician.

NOTE: You may notice a burning odor when the dryer is first
heated. This odor is common when the heating element is first
used. The odor will go away.

12

Advertising
Ce manuel est liée aux produits suivants: