Bissell PRODRY 7350 - Manuel (Page 11)

11
ww w. bi ss el l. ca 80 0. 26 3. 25 35
Net toy er/r em pla cer le TL R P ow erR olle r
MC
1. Faites passerl’interrupteur d’alimentation
enposition «O »(éteint) etdébranchez
l’appareil.
2. Retirezles deuxréser voirs,déc lenchezla
poignéeet placezl’a ppareilsur ledos.
3. Retirezles 6vis dela plaquede labase au
moyen d’untournevis àtête cruciformeet
mettez-lesde côtéa vecla plaquede base.
4. Tournez l’appareil surle côtéde manière
àce quele cordonlonge lesol.
5. Retirezles 2vis duprotecteur decourroie
etconser vez-les(Remarque :ces 2vis sont
identiquesaux 6vis dela plaquede base).
Retirezle hautdu protecteurde courroieet
lacheville dela brosse.
6. Déc roc hez la cou rro ie du TLR Pow erR olle re t
appuyez surle rouleaupour lefaire passer
parle trouen basdu protecteurde courroie.
7. Nettoyez leTLR PowerRoller enle rinçant
avec del’eau chaudeet dusa vondoux. Si
dés iré ,la iss ez- le séc her avan td ele rep lac er.
8. Pour lemettre enplace, poussezle pignon
duTLR PowerRoller denouveau dansle
trouet refixezla courroie.F aitesà nouveau
glisserla chevillede labrosse dansle TLR
PowerRoller etalignez lehaut duprotecteur
decourroie surla moitiéinférieure. Replacez
les2 vis.
9. Tournez l’appareil surle doset replacezle
secondbras pivotant.Assurez-vous quele
brasest bienen placeà lafois dansle TLR
PowerRoller etdans labase. Appuyez surle
TLRP owerRoller pourle logersous labuse.
10. Refixezla plaquede basea vecles 6vis.
Rangement de l’appareil
Ran gez l’a ppa rei l d ans un e a rm oir e o u a u
sou s-s ol e n v ue de la pro cha ine ut ilis ati on.
Ran gez l’a ppa rei l à l’a bri et da ns un lie u
sec . P uis qu’ il c ont ien t d e l’ eau , il ne do it
pas êt re ran gé dan s u n e ndr oit où il y a
un ris que de ge l. L e g el e ndo mm age ra les
com pos ant s in ter nes de l’a ppa rei l e t la
gar ant ie ser a a nnu lée .
E
ntretien et soin de l’appareil
5.
3.
6.
8c.
8b. 8a.
9.
11
w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5
Cleaning/replacing the TLR Power Roller TM
1. Turn power switch to OFF ( O ) and unplug
the machine.
2. Remove both tanks, detent the handle and
turn the machine on its back.
3. Remove the 6 screws from the sole plate
using a Phillips head screwdriver, set 6
screws and sole plate aside.
4. Turn the machine on its side so the cord side
is against the floor.
5. Remove the 2 screws from the belt guard
and set aside (Note: These 2 screws are the
same as the 6 sole plate screws). Remove
the top of the belt guard and brush dowel.
6. Unhook the belt from the TLR PowerRoller
and slide the roller down through the hole in
the belt guard bottom.
7. Clean the TLR PowerRoller by rinsing with
hot water and mild soap. Allow to dry before
replacing if desired.
8. To replace, push the cog of the TLR
PowerRoller back up through the hole and
re-attach the belt. Slide the dowel back
down through the TLR PowerRoller and line
the top of the belt guard over the bottom
half. Replace the 2 screws.
9. Turn the machine on to its back and
attach the second swing arm. Be sure the
arm is properly in place both on the TLR
PowerRoller and in the base. Push the TLR
PowerRoller down so it is nested under the
nozzle.
10. Re-attach the sole plate using the 6 screws.
Machine storage
Put the unit away in a closet or basement for
the next use. Store cleaner in a protected, dry
area. Since this product uses water, it must not
be stored where there is a danger of freezing.
Freezing will damage internal components and
void the warranty.
M
aintenance and care
5.
3.
6.
8c.
8b. 8a.
9.