Draw-Tite 22280 PROPORTIONAL WIRING ADAPTER - Manuel

Installation Instr uctions
Directives de Montage
Instrucciones de Instalación
Electric Trailer Brake Control
Wiring Adapter
Adaptateur pour câblage
de commande de frein de
remorque électrique
Adaptador del cableado de
control eléctrico del remolque
18280-037 Rev. A 11/02/04
READ THIS FIRST:
Read and f ollow all instructions carefully
before beginning installation.
LISEZ CECI EN PREMIER:
Lire et suivre toutes les instr
uctions
attenrivement avant le montage.
LEA ESTO PRIMERO:
Lea y siga todas las instr ucciones cuidadosa-
mente antes de iniciar la instalación.
e d
ENGLISH
CAUTION
Plug br ake control adapter into mating
receptacle on backside of brake control before
attaching to the vehicle connector.
d
1. Locate the v ehicle’s electric brake control
harness. The harness will be located under the
dash near the center console on most vehicles.
The harness for the Ford Full Size Van is
located underneath and left of the steering
column. The harness for the Ford Explorer/
Mercury Mountaineer is located behind the
vehicle glove box on the Passenger side. There
will be a 6-pin connector that mates with the
one on the adapter at the end of the harness.
2. V erify that there is battery power supplied to
the connector by carefully probing the connector
with a test light. This can also be accomplished
by following the wires to their source, ensuring
they do not dead end without connections
behind the instrument panel. For vehicle’s with
power supplied at this connector, proceed to
Step 4.
3. For vehicles with no power to the
electric brake control connector:
Using
an electric brake control wiring kit, route all
wires as described in the wiring kit installation
instructions. Cut the vehicle connector’s battery
feed wire, allowing enough wire remaining to
connect the battery wire from the brake control
wiring kit using the butt connector supplied.
Cut the vehicle connector’s trailer brake wire,
allowing enough wire remaining to connect the
trailer brake wire from the wiring kit using the
supplied butt connector.
4. Plug the br ake control adapter into the vehicle’s
electric brake control harness connector. Follow
all brake control manufacturer’s installation
instructions.
e
W ARNING
Complete the installation per the electr ic brake
control manufacturer’s instructions and mount
the unit as directed. Perform test procedures
as instructed.
W ARNING
Ov erloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. 4 axles: 8 brakes (24 amps)
Read vehicle’s owners manual and instruction
sheet for additional information.
VEHICLE STOP LAMP SWITCH TO BRAKE CONTROLLER
(INPUT)
COMMUTATEUR DE FEUX D'ARRÊT DU VÉHICULE AU
CONTROLE DE FREINS
INTERRUPTOR DE LUCES DE FRENADO DEL VEHICU-
LO AL CONTROLADO DE FRENO (ENTRADA)
FUSED TRAILER BRAKE CONTROLLLER BATTERY FEED
ALIMENTATION À FUSIBLE DE LA BATTERIE AU
CONTRÔLE DE FREINS
CONDUCTOR (CON FUSIBLE) DE LA BATERIA AL CON-
TROLADOR DEL FRENO DEL REMOLQUE
TRAILER BRAKE CONTROLLER (OUTPUT)
CONTRÔLE DE FREIN DE REMORQUE (SORTIE)
CONDUCTOR DEL CONTROLADOR DE FRENO (SALIDA)
AL FRENO ELÉCTRICO DEL REMOLQUE
HEAD LAMP SWITCH
TO VEHICLE RUNNING
LAMPS (UNUSED)
COMMUTATEUR DES
PHARES VERS LES
FEUX DE POSTION
DU VEHICULE
(UNUTILISES)
INTERRUPTOR DE
FAROS DELANTEROS
A LAS LUCES DE
RODAJE (NO SE USA)
GROUND
MISE À LA TERRE
TIERRA