Disc loding / unloding, Insertion / retrait du disque – Pioneer CDJ-100S Manuel d'utilisation

Page 15

Advertising
background image

15

<DRB1227>

En/Fr

BASIC OPERATIONS I/DEMARCHES DE BASE I

DISC LODING / UNLODING

1. Set the rear-panel POWER switch to ON.

Do not force a disc into the unit when the POWER
switch is set to OFF as this may damage the disc
and the unit.

2. Insert a disc.

÷ Hold the disc with label surface upwards, and insert

into the front panel disc loading slot .

÷ When playing an 8 cm disc, place the disc in a

commercially available CD adapter before inserting
in the loading slot.

÷ Only one disc can be loaded at a time. Never attempt

to load more than one disc at the same time, or
attempt to load a second disc when one disc has
already been loaded.

÷ When loading a disc, do not placing any twisting force

on the disc, or try to force the disc into the slot. Also,
do not attempt to interrupt or defeat the motion of
the disc when the player begins to draw a disc into
the slot or to eject a disc, since damage to the disc or
player could occur.

3. Press the EJECT button to remove discs.

÷ When the EJECT button is pressed, disc rotation stops

and the disc is ejected from the loading slot.

÷ If the disc fails to be ejected when the EJECT button

is pressed, the accessory forced eject pin can be
inserted into the front-panel’s forced eject hole to eject
the disc.

Insert straight
Insérer en ligne droite

CAUTION

Do not attempt to press a disc back into the slot
when the EJECT indicator appears. Pressing a disc
back into the slot while the EJECT indicator appears
may cause the player to stop. In this case, press the
EJECT button again and wait until the EJECT indi-
cator goes out before reinserting the disc.

INSERTION / RETRAIT DU
DISQUE

Label surface up
Surface étiquetée vers le haut

1. Régler l’interrupteur POWER du panneau

arrière sur ON.

Sous peine de les endommager, ne pas forcer
l’entrée d’un disque dans l’appareil si l’interrupteur
POWER n’est pas allumé ‘OFF).

2. Insérer un disque.

÷ Diriger l’étiquette du disque vers le haut et insérer

celui-ci dans la fente de chargement du disque sur le
panneau avant du lecteur CD.

÷ Pour reproduire un disque de 8 cm, insérer celui-ci

dans un adaptateur CD disponible dans le commerce
avant de l’introduire dans la fente du logement.

÷ Insérer un seul disque à la fois. Ne jamais essayer

d’introduire plusieurs disques en même temps ou
d’insérer un second disque quand il y en a déjà un
dans le logement.

÷ Lors de son insertion, ne pas exercer de torsion sur

le disque ou essayer d’introduire de force par la fente
du logement. Sous peine d’endommager le disque
et le lecteur, ne pas essayer d’interrompre ou de faire
obstacle au mouvement du disque lorsqu’il est attiré
dans le logement ou qu’il en est éjecté.

3. Appuyer sur la touche EJECT pour retirer un

disque.

÷ Lorsque la touche EJECT est actionnée, le disque

cesse de tourner et il est éjecté par la fente du
logement.

÷ Si le disque ne ressort pas quand la touche EJECT

est actionnée, la broche d’éjection forcée fournie
comme accessoire peut être insérée dans l’orifice
d’éjection forcée du panneau avant afin de faire
ressortir le disque.

ATTENTION

Ne jamais essayer de repousser un disque dans le
logement pendant que l’indicateur EJECT est
allumé, car ceci provoquerait l’arrêt du lecteur. Dans
ce cas, appuyer à nouveau sur la touche EJECT et
attendre jusqu’á ce que s’éteigne l’indicateur EJECT
avant d’insérer à nouveau le disque.

Advertising