JVC LD-HD2KBE - Manuel (Page 22)

Adjustments and Settings Using Menus (continued)
22
.................................................................................................
SET: NTSC SCANRATE
(Output scan rate setting for NTSC signals)
Sets the output scan rate of NTSC signals. Set to
A1920 ן 1080B.
● Press the [STORE] button twice to confirm the setting and
store it as a profile. Please refer to 19 and 26 for details on
profile setting.
.................................................................................................
SET: PAL SCANRATE
(Output scan rate setting for PAL signals)
Sets the output scan rate of PAL signals. Set to
A1920 ן 1080/50HzB.
● Press the [STORE] button twice to confirm the setting and
store it as a profile. Please refer to 19 and 26 for details on
profile setting.
.................................................................................................
SET: ACTIVE OUTPUT
(Output signal setting)
Sets whether to output analog signals (BNC, D-sub) or
digital signals (DVI) to the output terminal of this unit.
● Select AANALOG RGB+DVIB to output both digital and
analog signals. However, output of YPrPb signals is not
possible.
● Each of the output format can be stored as a separate
profile. ( A Pages 19, 26)
● There will be no output to the analog terminal when HDCP
signals are input to the DVI input terminal of this unit. In
this case, an
AENCRYPTED SOURCE ANALOG OUT
DISABLE B message will appear on the LCD.
.................................................................................................
SET: SCREEN SHAPE
(Screen shape setting for projector)
Sets the screen shape of the projector that is connected
to this unit.
oWIDESCREEN
Choose this when projecting 16:9 or 2.35:1 images
from the projector onto a wide screen.
oWIDE 4:3
Choose this when projecting a 4:3 image from the
projector onto a wide screen. (Not available on units
scanning at rates below 720p.)
o4:3
Select this when using a 4:3 screen.
.................................................................................................
SET: ANALOG BLACK LVL
(Level setting for black analog signals)
Sets the black signal level of the YPrPb component video
signal.
.................................................................................................
SET: COMP SYNC ON H
(Composite sync signal setting)
Sets the horizontal/vertical sync signals when connected
via the analog RGB output (4-wire connection). When this
is set to
AONB, composite sync signals will be output from
the [H SYNC] terminal.
● This processor is used via a DVI connection to the
projector, and therefore this setting is not required.
● Setting is enabled when you select AANALOG RGB+DVIB
or AANALOG RGBB in the ASET: ACTIVE OUTPUTB
setting.
Setup Menu Configuration
Setting Values:
1280
ן 720, 1024 ן 768, 1280 ן 768, 1366 ן 768,
1440 ן 960, 1280 ן 1024, DILA, DILA3,
1920 ן 1080, 1400 ן 788, 1920 ן 540, 800 ן 600
Default Value: 1280 ן 720
Setting Values:
1280
ן 720/50Hz, 1024 ן 768/75Hz, 1024 ן 768/
100Hz, 1920 ן 1080/50Hz, 720 ן 576/50Hz, 720 ן
576/100Hz
Default Value: 1280 ן 720/50Hz
Setting Values:
ANALOG RGB+DVI, ANALOG YPrPb, DVI, ANALOG
RGB
Default Value: ANALOG RGB+DVI
Setting Values: WIDESCREEN, WIDE 4:3, 4:3
Default Value: WIDESCREEN
Setting Values: 0 IRE, 7.5 IRE
Default Value: 7.5 IRE
Setting Values: OFF, ON
Default Value: OFF
LD-HD2KU_E.book Page 22 Thursday, November 17, 2005 4:27 PM