Breville the Milk Cafe BMF600XL Issue - E11 - Manuel (Page 7)

12 13
OPERATING yOUR BREvILLE MILK CAFé™ OPERATING yOUR BREvILLE MILK CAFé™
4. Pour the required amount of cold,
fresh (or freshly opened) milk into the
milk jug then cover with the jug lid.
Always use cold milk and fill the milk
jug between the MIN and MAX level
markings. Overfilling may result in
spillage, while underfilling prevents the
frothing disc from working optimally.
NOTE
Never operate without the minimum
level of liquid in the milk jug. The milk
frother will automatically turn off if the
milk jug is empty. If this occurs, you
will need to wait for the milk frother
to cool down before re-use, refer to
page 14.
MIN MAX
For optimum results, there are different
measurement markings within the milk
jug. The chart on the right shows the
approximate number of cups produced
at each of the measurement markings.
This is a guide only as the frothing
disc selected and the type of milk, for
example whole milk (vitamin D), 2%,
1%, fat-free, half-and-half etc., can create
different amounts of froth.
JUG MARKING FROTHING dISC MAKES
APPROX.
HOT CHOC MAX
25 fl.oz (750ml) Cappuccino
(recommended)
OR
Latte
3 cups
CAPP / LATTE MAX
16 fl.oz (500ml) Cappuccino
OR
Latte 2-3 cappuccinos
8 fl.oz (250ml) Cappuccino
OR
Latte 1-2 cappuccinos
MIN Cappuccino
OR
Latte 1 cappuccino
NOTE
For optimum froth, do not exceed the
CAPP/LATTE MAX (16 fl.oz, 500ml)
measurement marking inside the
milk jug.
5. Ensure the jug lid is securely attached
and the outside of the milk jug is clean.
Place the milk jug onto the power base,
ensuring the jug is sitting flat.
6. Turn the START | STOP push-dial
to the desired temperature. When
frothing milk for a cappuccino or
latte, we recommend staying within
the ‘OPTIMUM MILK TEMP’ range,
however this is up to your personal
preference.
If the temperature setting is changed
during operation, the milk frother will
stop at the new temperature selected.
The exception is if a lower temperature
is selected mid-cycle and the milk has
already exceeded the lower temperature.
In this case, the milk frother will
immediately stop.
9. Clean the milk jug and frothing disc
immediately after use. Both will be hot,
so follow the instructions on page 17 and
allow them to cool completely before
disassembling.
NOTE
When frothing multiple batches,
to prevent the Boil Dry Protection
from activating (see page 14), we
recommend allowing the milk jug
to cool for approximately 5 minutes,
or filling the milk jug with water for
faster cooling. For best results, we
also recommend cleaning the milk
jug and frothing disc before re-use.
NOTE
After frothing the first batch of
milk you may notice the power base
begin to hum. This is normal. It
is the cooling fan preventing the
milk frother from overheating and
will automatically cease to hum
once adequately cooled. During
this time, you may still use the milk
frother unless the Boil Dry Overheat
Protection as been activated
(see page 14).
USING THE ‘COLd STIR’ SETTING
The ‘Cold Stir’ setting allows you to
stir already cold or hot milk without
additional heat.
Use it to froth milk for cold beverages
such as an iced cappuccino; to blend in
syrups and flavorings for an iced chocolate
or mocha; or to stir in dissolvable instant
drinking powders into milk or water.
The ‘Cold Stir’ setting will operate for 60
seconds before automatically stopping. You
can re-select the ‘Cold Stir’ setting if desired.
ONLY PRESS ONCE, FIRMLY
7. Only press the START | STOP
push-dial once, firmly.. Frothing has
started once the milk frother beeps
once and the button surround slowly
flashes. If the milk frother does not do
this, try pushing the START | STOP
push-dial again to ensure it has been
properly activated.
NOTE
Do not remove the milk jug from the
power base during operation. Doing
so may dislodge the frothing disc
and cause a grinding noise. Always
press the center of the START | STOP
push-dial before removing the jug.
Operation has stopped once the button
surround has stopped flashing.
WARNING
Appliance surfaces will be hot during
and after operation.
8. When the milk has reached the selected
temperature, the milk frother will
automatically stop and beep twice. This
will take anywhere between 2 -7 minutes
depending on the quantity of milk used.
Carefully remove the milk jug from the
power base as the milk jug and contents
will be hot. Be careful not to place the
milk jug on a table cloth, plastic surface
or heat sensitive surface which may
scorch or melt. Remove the jug lid, pour
and/or spoon out the frothed milk.