Breville BES900XL - Manuel (Page 7)

12 13
OPERATING yOUR BREvILLE dUAL BOILER™ OPERATING yOUR BREvILLE dUAL BOILER™
fIRST USE
Initial Start Up
• Fill water tank with cold, preferably
filtered water. You can do this by either
opening the top-fill water tank lid (push
to open), or by removing the water tank
at the back of the machine.
• Check STEAM LEVER and HOT
WATER dial are in the CLOSED
position.
• Press the POWER button to switch the
machine On. The POWER button will
flash and the LCD screen will display the
current espresso boiler temperature.
• A pumping sound will be heard
indicating empty boilers are being
filled with water for the first time. This
is normal. During this time, rotate the
HOT WATER dial to the OPEN position
to “prime” the espresso boiler. When
water starts to flow from the Hot Water
outlet, rotate the HOT WATER dial to
the CLOSED position.
• When the machine has reached the default
operating temperature (200˚F / 93˚C), the
POWER button light will stop flashing and
the MANUAL, 1 CUP and 2 CUP buttons
will illuminate. The machine is now in
STANDBY mode, ready for the next step
‘Flushing The Machine’.
flushing The Machine.
When the machine has reached STANDBY
mode, run the following 3 steps:
1. Press 2 CUP button to run water
through group head.
2. Rotate HOT WATER dial to
the OPEN position and run for
30 seconds.
3. Move STEAM LEVER to the OPEN
position and run for 10 seconds.
Repeat this cycle until tank is empty.
TIP
To easily maneuver your machine,
use the drop down swivel foot located
under the drip tray. When turned to
the UNLOCK position, the swivel
foot drops down and lifts the machine
upwards, making it easier to access
the rear water tank or reposition the
machine to another location.
START UP
Press the POWER button to switch the
machine On. The POWER button will flash
and the LCD screen will display the current
espresso boiler temperature.
When the machine has reached the default
operating temperature (200˚F / 93˚C), the
POWER button light will stop flashing and
the MANUAL, 1 CUP and 2 CUP buttons
will illuminate. The machine is now in
STANDBY mode ready for use.
NOTE
The machine is in START UP mode
when the POWER button light is
flashing. During this time, the
MANUAL, 1 CUP and 2 CUP buttons
will be disabled. Similarly, if you press
the MENU button during START UP
mode and select SHOT VOL or
CLEAN CYCLE, the LCD screen will
display BUSY.
Always wait until the machine is in
STANDBY mode. This is when the
POWER button light stops flashing
and the MANUAL, 1 CUP and 2 CUP
buttons illuminate.
POWER SAvE MOdE
The machine will enter POWER SAVE mode
after remaining idle for 1 hour and turn Off
completely if not used for a continuous
4 hour period (refer to ‘Auto Power Off’,
page 21).
Pressing any button during POWER SAVE
mode (except POWER), or operating the
STEAM LEVER or HOT WATER dial will
cause the machine to enter START UP mode.
Pressing the POWER button during
POWER SAVE will turn the machine Off.
LCd INTERfACE
display modes
3 modes can be displayed on the LCD
screen: Shot Temp, Shot Clock or Clock.
Press UP or DOWN arrow to change the
display mode.
1. Shot Temp
Displays selected extraction temperature.
The default is set at 200°F (93°C), but
can be changed from 190°F - 205°F
(86°C - 96°C).
See ‘Extraction Temperature’, page 16.
2. Shot Clock
Displays duration of current espresso
extraction in seconds. See ‘Extraction
Guide’, page 27.
3. Clock
Displays current time. The default is
12:00AM if the time has not been set.
See ‘Set Clock’, page 17.
GENERAL OPERATION
1 CUP BUTTON
Press 1 CUP button once to extract a single
shot of espresso at the pre-programmed
volume (approx. 1oz / 30ml). The extraction
will start using the low pressure pre-infusion.
The machine will stop after 1 CUP volume
has been extracted and will return to
STANDBY mode.