Sony CDX-505RF - Manuel (Page 10)

Listening to a CD
1
Turn on the FM tuner of the car audio.
2 Adjust the selected transmitting frequency
with the wired remote.
(88.3 MHz/88.5 MHz/88.7 MHz/88.9 MHz/
89.1MHZ/89.3 MHz/89.5 MHz/89.7 MHz/
89.9 MHz)
3 Press the ►!!.
CD playback start.
4
Adjust the volume with the volume control
on the car audio.
All the tracks play from the begining.
Stopping CD play
Press (OFF).
Notes
• When CD playback is stopped, you may hear some noise
from the speakers. To prevent this from happening, turn the
volume down before stopping CD playback.
• If you turn off the ignition switch of your car without
stopping CD playback, it will automatically resume CD
playback from where it was stopped the next time you turn
on the ignition switch.
Listening to the radio or a tape
Be sure to stop CD playback before you start
listening to the radio or a tape.
Note
Be sure to stop CD playback, otherwise there may be some
interference with radio reception.
Changing the transmitting
frequency
Because this unit processes CD playback sound
through an FM tuner, there may be interference
noise during CD playback. In this case change the
frequency of the modulated RF signal transmitted
from hideaway unit. The initial setting is 88.3
MHz.
1 Press ( REP) for more than two seconds.
2 Press either the left or right side of ( ams )
to select the frequency.
Each time you press CAMS), the frequencys
change as follows-.
I : 88.3 MHz
88.9 MHz -
89.5 MHz ■
I : 89.9 MHz •
89.3 MHz ■
88.7 MHz ■
► 88.5 MHz -
► 89.1 MHz -
► 89.7 MHz ■
► 89.7 MHz -
► 89,1 MHz-
► 88.5 MHz ■
> 88.7 MHz -
> 89.3 MHz ■
> 89.9 MHz
>89.5 MHz-
>
88.9 MHz ■
> 88.3 MHz
3 Press ( REP) for more than two seconds.
Note
Be sure to set the frequency of your FM tuner to the newly
selected frequency.
Changing the output level
You can select the output level from the CD
changer. Normally the system is used at the
initial output level; change the level if necessary.
Playing tracks in random order
— Shuffle Play
You can select:
• SHUF 1 to play the tracks on'the current disc in
a random order.
• SHUF 2 to play all the discs in a random order.
Press (SHUF) repeatedly until the'desired
setting appears (SHUF1 or SHUF2).
After five seconds, the shuffle play starts.
Each time you press (SHUF), the display
changes as follows:
-> SHUF1 -► SHUF2
-------- Cancel (SHUF off) ◄-------------
To go back to the normal playback mode,
press
(SHUF) until the "SHUF" disappears.
1 Press ( REP ) for more than two seconds.
2 Press CMD-
■
nn n
3UU u
Initial setting
Press either the left or right side of ( am s )
to select the output level.
To decrease the output level
n
!U
To increase the output level
■
nn nn
HUU UU
4 Press ( rep ) for more than two seconds.
Playing tracks repeatedly
— Repeat Play
You can select:
• REP 1 to repeat the track.
• REP 2 to repeat the disc.
Press (REP) repeatedly until the desired
setting appears (REP1 or REP2).
. After five seconds, the repeat play starts.
Each time vou press
changes as follows:
REP 1 —► REP 2
, the display
Cancel (REP off) —|
To go back to the normal playback mode,
press C
REP) until ''REP'' disappears.