Aquascape MicroSpot Light (02407) - Manuel (Page 3)

Legal Warnings
Except as stated in the warranty, there are no other representatives or warranties related to
the product or its use. THE USER SHALL DETERMINE THE SUITABILITY OF THE PRODUCT FOR
THE USER’S INTENDED USE, AND THE USER ASSUMES ALL RISKS AND LIABILITIES WHATSO-
EVER IN CONNECTION THEREWITH. Seller and manufacturer’s only obligation is to repair and
or replacement of submersible light housing as stated below. ALL IMPLIED WARRANTIES ARE
HEREBY EXCLUDED, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Neither seller nor the manufacturer
shall be liable for any injury loss, or damage whether direct, incidental, or consequential
arising out of the use or inability to use the product.
The national Electric Code, Article 680-14 (A), requires a Ground Fault Circuit Interceptor
(GFCI) to be installed in the branch circuit supplying fountain equipment rated above 15 volts.
WArNING!
It is good practice whenever working in or near water to have all electrical devices plugged
into a ground fault circuit interrupter(GFCI) that has been installed by a licensed electri-
cian. Do not put stake through liner. Spot light MUST be completely submerged in water for
proper cooling of light bulb. COVER TO LIGHT MUST BE TIGHT AT ALL TIMES TO PREVENT
ANY LEAKING .
1) Getting to Know Your MicroSpot™ Light
The MicroSpot™ Light comes with:
20 Watt underwater light with 15 ft. cord
• 5 interchangeable lenses (clear, blue, red, green, and amber)
• Adjustable plastic light stand.
The MicroSpot™ Light with transformer comes with:
• 5 interchangeable lenses (clear, blue, red, green, amber, and red)
• Adjustable plastic light stand.
• Transformer
MicroSpot
™
Light
Installation & Maintenance Instructions
3
) Installing the Light
It is easiest to install and conceal the MicroSpot™ light(s) prior to putting the gravel in the
pond. Find a desirable location for the light(s). We suggest positioning the lights so they
are facing away from the main viewing area. Double-check to make sure that the cover
is fastened tightly down. The light is designed to be incorporated into the boulder wall by
“tucking” it in-between a set of boulders. The boulders can be adjusted around the light in
order to “lock” light into position. Simply take the cord and plug into transformer, plug in
transformer and enjoy!
MicroSpot™ 20 Watt light is designed to be used COMPLETELY submerged in water. Be
careful to not place light fixture in the “ice-zone” of the pond, this may cause cracked
lenses. We suggest placing the light fixture 8 inches or more below the surface of the water.
You can place the fixture in the “ice-zone” as long as you remove it before winter ad leave
outside the pond or in a position that it will not freeze in the pond. Replacement lenses are
available if needed.
3) replacing the Light Bulb
1. Make sure the transformer is unplugged before changing the bulb.
The light housing must be above water to properly service the light bulb.
2. Unscrew the plastic cap from the front of the light housing unit.
3. Remove the glass lens and o-ring from light housing.
4. Use a thin flat-head screwdriver to pry the light up and out of the housing.
Note: Removing the halogen light by pulling the bulb is not recommended.
5. Insert the new bulb by inserting the two metal plugs into the connector
Note: Do not touch the halogen light inside the assembly.
6. The o-ring and lens can now be installed back into place. Make sure there
is no dirt or debris on the lens, o-ring, and assembly prior to reassembling.
7. Attach the cap back onto the light housing.
8. Test to make sure light works
9. Position light back into pond.
Cover
Lens
ring Seal
Bulb
Case
Transformer
Plastic Base
02407 MicroSpot Light Instructio3 3 10/2/06 2:34:32 PM