Yorkville Sound LS700P - Manuel (Page 4)

2
the 9 o’clock position except when
operating at low levels. For most
applications the control should be set
between 0dB and +20dB.
A setting of 0dB on the SUBWOOFER
LEVEL control is the correct starting point
when setting up a sound system. From there
the sound can be adjusted for best sound.
The 0 dB mark refers to the setting that will
give full power when the line input is used
and the input signal is at a level of +4 dBV.
This also is the setting to give a sensitivity of
2.83 Vrms (1 watt 8-Ohms) for 100 dB spl
when set for speaker level input. With a
typical full range companion speaker this
will give flat response. In either line or
speaker operation it will usually be desirable
to set the control at +3 to +6 to give some
bass boost at low power levels. At levels
approaching full power the built-in limiter
will automatically reduce the gain to
prevent over powering the subwoofer.
Operation with settings significantly above
+12 may clip the circuitry in the subwoofer
reducing the dynamics of the music. Setting
the subwoofer gain above +12 is only
appropriate at low operating level.
3 3.. IIn np pu utt G Grro ou un nd d S Sw wiittc ch h
The LS700P expects the source feeding it
to be grounded. A system comprised
entirely of ungrounded equipment may
cause the LS700P to hum or buzz. If you
have a buzz or hum problem, try setting
the switch to the "GROUNDED" position.
The switch should otherwise be left in the
"UNGROUNDED" position. Do not use the
grounded position with an amplifier
operating in bridged mode or when the
sleeve of the input signal is live.
4 4.. IIn np pu utt L Le ev ve ell S Sw wiittc ch h
A switch is provided to switch input levels
between speaker level and line level. The
switch should be set to speaker level when
the LS700P is fed from the output of an
amplifier or powered mixer. The line level
position is for when the LS700P is fed a
signal from a processor, electronic
crossover or the output of an unpowered
mixer. When using the line level mode the
use of balanced (Tip, Ring, Sleeve) cables
will reduce the sensitivity to hum and buzz.
5 5.. S Stte erre eo o IIn np pu utt a an nd d P Pa arra alllle ell
T Th hrru u J Ja ac ck ks s
For normal operation, connect the LS700P
just like an ordinary speaker, along with the
Full-Range speakers and set the Input
Level switch to SPEAKER. If the audio
source does not have a ground pin on the
AC cord, the Input Ground switch must be
set to GROUND (GND). The LS700P may be
plugged in before or after the Full-Range
speakers. Use the Left and Right Inputs
when using a single LS700P in a stereo
system. Use either the Left or the Right
inputs when using separate LS700P's for
each side (or when used in a Mono
system). The LS700P does not alter the
signal to the Full-Range speakers, and will
not draw any power from the host
amplifier driving them. Please note that an
external crossover is not necessary.
As well as accommodating the full
range speakers, the PARALLEL THRU jacks
allow many LS700Ps to be connected in a
string (or otherwise in parallel). There is no
practical limit to the number of LS700Ps
that may be connected together.
AT HIGH POWER LEVELS WHEN THE LIMITER IS OPERATING INCREASING THE SUBWOOFER LEVEL CONTROL WILL NOT
INCREASE THE OUTPUT. DO NOT INCREASE SETTING WHILE OPERATING AT HIGH LEVELS.
USER NOTE:
This Subwoofer may be driven from Speaker Level
or Line Level signals. If an élite processor is used,
this Subwoofer should be plugged into the SUB
output of the processor. The
High–Frequency
Cutoff should be set to 150-Hz and the Input Level
should be set to LINE. For Line
Level operation a balanced (
Tip
Ring Sleeve) cable should be
used. If the system is being
operated
without a processor,
this Subwoofer can be
connected to the output of the
power amplifier as shown in the
diagrams and the Input Level
should be set to SPEAKER. If
none of the equipment has a U-
ground, the INPUT GROUND
should be set to
GROUNDED.
Otherwise the INPUT GROUND
should be set to the position that
best minimizes the hum.
Refer to the Owner's
Manual for other modes
of operation
+3
-3
+10
+30
+20
dB
LS700P
Yorkville
DESIGNED & MANUFACTURED BY YORKVILLE SOUND • TORONTO, CANADA
INPUT GROUND
INPUT LEVEL
LEFT
(mono)
RIGHT
HIGH
FREQUENCY
CUT OFF 125 Hz
POWER
100 Hz 150 Hz
SUBWOOFER
LEVEL
PARALLEL
THRU
INPUT
PARALLEL
THRU
INPUT
UNGROUNDED
GROUNDED
SPEAKER
LINE
0
1
2
3
5
4