Sony DVP-8306 - Manuel (Page 35)

Locating a Scene or Track You Want
35 EN
Locating a Scene or Track You Want Locating a Scene or Track You Want Settings and Adjustments Settings and Adjustments
Settings for Sound (INITIAL
SETUP 2)
Select “ 2 ” after pressing SET UP.
“INITIAL SETUP 2” allows you to set the sound
according to the playback conditions.
Default settings are underlined.
pTRACK SELECTION
Gives the Dolby Digital (AC-3) format priority when you play
a DVD on which multiple audio formats are recorded. If
multiple audio channels are recorded in Dolby Digital (AC-3)
format, the higher-numbered channel audio recorded in
Dolby Digital (AC-3) format is played.
• OFF: No priority given.
• AUTO: Priority given.
Notes
• When you set this item to “ON”, the language may change
depending on the “AUDIO” settings in “LANGUAGE
SETUP.” The “TRACK SELECTION” setting has higher
priority than that of “AUDIO” settings in “LANGUAGE
SETUP” (page 33).
• Depending on the DVD, the audio with priority may be
predetermined. In this case, you cannot give priority to the
Dolby Digital (AC-3) format by selecting “AUTO.”
pSURROUND*
Switches the mixing down methods when you play a DVD on
which the sound in Dolby Digital (AC-3) format is recorded.
• ON: when the player is connected to an audio component
that conforms to Dolby surround, Dolby Pro Logic
surround, etc.
• OFF : when the player is connected to a normal audio
component.
* The setting affects the connectors as follows:
–LINE OUT (AUDIO 1, 2) connectors
–DIGITAL OUT (OPTICAL, COAXIAL) connectors.
pDIGITAL OUT
Switches the methods of outputting audio signals from the
DIGITAL OUT OPTICAL and COAXIAL connectors on the
rear panel of the player.
• PCM: when the player is connected to an audio component
without a built-in Dolby Digital (AC-3) decoder
If you play the Dolby Digital (AC-3) sound track, the player
outputs no sound.
• DOLBY DIGITAL/PCM: when the player is connected to
audio component with a built-in Dolby Digital (AC-3)
decoder
• D-PCM (Downmix PCM): when you play the Dolby Digital
(AC-3) sound tracks, the output audio signals are mixed
down to 2 channels. By the settings of the item
“SURROUND,” you can select whether the signals contain
the surround component or not. The output audio signals
from the 5.1 OUTPUT connectors are also mixed down in
the same way. To enjoy the original Dolby Digital (AC-3)
sound through the 5.1 OUTPUT connectors, do not set this
item to “D-PCM.”
Note
Select the setting correctly. Otherwise, no sound or
strange sound will come out from the speakers,
affecting your ears or causing the speakers to be
damaged.
pAUDIO DRC (Dynamic Range Control)
Makes the sound clear with the volume turned down at night,
etc. when you play a DVD. This affects the output from the
DIGITAL OUT connectors only when “DIGITAL OUT” in
”INITIAL SETUP 2” is set to “PCM,” the output from the
LINE OUT (AUDIO 1,2), and 5.1 OUTPUT connectors.
• OFF: Normally select this position.
• ON: makes the sound clear even if you turned the volume
down.
Note
When you play DVDs without the AUDIO DRC function,
there may be no effect on the sound.
pAUDIO ATT (attenuation)
Selects the setting of the output from the LINE OUT (AUDIO
1, 2) and 5.1 OUTPUT connectors according to audio
equipment to be connected.
• OFF: turns off the audio attenuation.
• ON: reduces the audio output level so that no sound
distortion occurs.
Note
The setting does not affect the output from the DIGITAL OUT
OPTICAL and COAXIAL connectors.
pAUDIO FILTER
Selects the type of digital filter to reduce the noise higher
frequency than 22.05kHz (fs 44.1kHz), 24kHz (fs 48kHz) or
48kHz (fs 96kHz).
• SHARP: makes the sound clear and provides smooth sound
reproduction. Normally set this position.
• SLOW: makes the sound warm and deep.
Note
Depending on the disc, there may be no effect on the sound.
I N I T I A L S E T U P 2
S U R R O U N D : O N
D I G I T A L O U T :
A U D I O D R C :
P C M
O F F
Q U I T ENTER SETUP
O F F A U D I O A T T :
A U D I O F I L T E R :
T R A C K S E L E C T I O N :
S H A R P
O F F
1 2 1 2