Sony TA-VE910 - Manuel (Page 22)

22 EN
Sound Adjustment
Adjusting the equalizer parameters
Adjust the equalization (bass or treble) of the front,
center and rear speakers for optimum sound.
The following adjustments effect all sound fields
simultaneously.
1
While playing a component, press DPC MODE
repeatedly until the EQ indicator lights up.
2
Use the digital processing control buttons ( /
) to select the parameter to be set and use the
buttons ( / ) to select the setting.
After selecting the parameter, you can use BAND
on the remote to switch between BASS and
TREBLE.
To set Select And set between
bass level of the
front speakers F: BASS –10.0dB and
+10.0dB (in 0.5 dB
steps)
bass frequency of
the front speakers F: BASS 99Hz and 992Hz (in
21 levels)
treble level of the
front speakers F: TREBLE –10.0dB and
+10.0dB (in 0.5 dB
steps)
treble frequency of
the front speakers F: TREBLE 1.0kHz and 8.6kHz
(in 21 levels)
bass level of the
center speaker C: BASS –10.0dB and
+10.0dB (in 0.5 dB
steps)
bass frequency of
the center speaker C: BASS 99Hz and 992Hz (in
21 levels)
treble level of the
center speaker C: TREBLE –10.0dB and
+10.0dB (in 0.5 dB
steps)
treble frequency of
the center speaker C: TREBLE 1.0kHz and 8.6kHz
(in 21 levels)
bass level of the rear
speakers R: BASS –10.0dB and
+10.0dB (in 0.5 dB
steps)
bass frequency of
the rear speakers R: BASS 99Hz and 992Hz (in
21 levels)
treble level of the
rear speakers R: TREBLE –10.0dB and
+10.0dB (in 0.5 dB
steps)
treble frequency of
the rear speakers R: TREBLE 1.0kHz and 8.6kHz
(in 21 levels)
3
Repeat Step 2 if necessary.
z
You can turn off the equalizer adjustments without
erasing them
Z
Press EQ/TONE on the remote.
Note
You may hear some noise as you adjust the parameters.
Adjusting the effect and surround sound
parameters
Change the surround parameters to fit your listening
situation. See the chart on page 21 for parameters you
can adjust in each sound field.
1 Press DPC MODE repeatedly until the SUR
indicator lights up.
2
Use the digital processing control buttons ( /
) to select the parameter to be set and use the
buttons ( / ) to select the setting.
To Select And set
set the overall
presence of the
sound field
1)
EFFECT among 21 levels
set the level of the
high frequencies
to alter the sonic
character of your
listening
environment WALL between S (soft wall)
and H (hard wall)
(in 17 levels)
select your seat
position (front or
rear) to simulate
the acoustics of
the selected
position SEAT between F (front)
and R (rear)
(in 17 levels)
select your seat
position (left or
right) to simulate
the acoustics of
the selected
position SEAT between L (left) and
R (right)
(in 17 levels)
set the length of
time required for
the reverberation
from a given
sound to
attenuate to –60
dB REVERB between S (short)
and L (long)
(in 17 levels)
attenuate the level
of the LFE (Low
Frequency
Extension)
channel output
from the
subwoofer
2)
LFE MIX among MUTE,
–20.0dB to 0dB
(in 0.5 dB steps)
compress the
dynamic range of
the sound track D.RANGE
COMP among OFF, 0.1 to
0.9, STD, MAX
3)
1) When the sound field is KARAOKE, this parameter
adjusts the vocal presence. The higher the setting, the
less dominant the vocal sound.