Maytag MTW5805TW - Manuel (Page 17)

17
Agitator operation
■ The top of the agitator is loose, or moves in only one direction. This is normal.
Dispensers clogged or bleach leaking
■ Did you follow the manufacturer’s directions when adding detergent and fabric softener
to the dispensers (on some models)? Measure detergent and fabric softener. Slowly pour
into the dispensers. Wipe up all spills. Dilute fabric softener in the fabric softener
dispenser.
■ Did you put powdered or color-safe bleach into the liquid chlorine bleach dispenser (on
some models)? Add powdered or liquid color-safe bleach directly to the basket. Do not
use the chlorine bleach dispenser for color-safe bleach.
Washer Operation
Washer won’t run, fill, rinse or agitate; washer stops
■ Is the power cord plugged into a grounded 3 prong outlet? Plug power cord into a
grounded 3 prong outlet.
■ Are you using an extension cord? Do not use an extension cord.
■ Is the indicator on the Timer knob properly lined up with a cycle? Turn the Timer knob to
the right slightly and pull to start.
■ Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from
the washer. Remove any accumulated film or particles. Reinstall hoses, turn on water and
check for leaks.
■ Are both the hot and cold water faucets turned on? Turn on the water.
■ Is the water inlet hose kinked? Straighten the hoses.
■ Does the water level seem too low, or does the washer appear to not fill completely? The
top of the agitator is much higher than the highest water level. This is normal and
necessary for clothes to move freely.
■ Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset
the circuit breaker. If the problem continues, call an electrician.
■ Is the washer in a normal pause in the cycle? The washer pauses for about 2 minutes
during certain cycles. Allow the cycle to continue. Some cycles feature periods of
agitation and soak.
■ Is the washer overloaded? Wash smaller loads.
■ Is the lid open? The lid must be closed during operation. Washer will not agitate or spin
with the lid open.
Washer won’t drain or spin
■ Is the drain hose clogged, or the end of the drain hose more than 96" (244 cm) above the
floor? See “Connect Drain Hose” for proper installation of drain hose.
■ Is the lid open? The lid must be closed during operation. Washer will not agitate or spin
with the lid open.
■ Is there excessive sudsing? Always measure detergent. Follow manufacturer’s directions. If
you have very soft water, you might need to use less detergent.
Washer continues to fill or drain; cycle seems stuck
■ Is the top of drain hose lower than the water level in washer? The top of the hose must be
higher than the water level in the washer for proper operation. See “Drain System.”
■ Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe? The
drain hose should be loose yet fit securely. Do not seal the drain hose with tape. The hose
needs an air gap. See “Secure the Drain Hose.”
Wash/Rinse temperature not what I selected
■ Are the hot and cold water inlet hoses reversed? See “Connect the Inlet Hoses” for more
information. As your frequency of loads washed increases, the water temperature may
decrease for hot and warm temperatures. This is normal.
Washer Results
Load too wet
■ Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).
■ Did you use a cold rinse? Cold rinses leave loads wetter than warm rinses. This is normal.
Residue or lint on load
■ Did you sort properly? Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING