Eskimo HC40Q8 - Manuel (Page 7)

7
Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT
Operator's Manual
Propane Powered Ice Auger
ENGLISH
Engine Maintenance
Please read this manual completely. Observe the
recommendations to extend the life of your engine.
Good maintenance is essential for safe, economical, and
trouble-free operation. It will also help reduce air pollution.
To help you properly care for your engine, the following
pages include a maintenance schedule, routine inspection
procedures, and simple maintenance procedures using basic
hand tools.
Other service tasks that are more difficult, or require special
tools, are best handled by professionals and are normally
performed by a technician or other qualified mechanic.
Maintenance, replacement or repair of the emissions
control devices and systems may be performed by any
non-road engine repair establishment or individuals.
However, all authorized warranty repairs must be handled
by an authorized service center.
The maintenance schedule applies to normal operating
conditions. If you operate your engine under unusual
conditions, such as sustained high-load or high-temperature
operation, or use in unusually wet or dusty conditions, consult
your servicing dealer for recommendations applicable to your
individual needs and use.
Steps For Working On Engine Or Auger
1. Turn engine switch to OFF position.
2. Disconnect the spark plug wire from the spark plug.
3. Securely place the disconnected spark plug wire away
from the spark plug and any metal parts. This must always
be done or arcing may occur between spark plug wire and
metal parts.
4. Replace or repair the part on the engine or auger.
5. Check all parts that were repaired, or removed during
repair, that they are secure and fit correctly.
NOTE: All repair parts must come from the factory. Never
replace parts that are not specifically designed for
the engine or auger.
6. Reconnect spark plug wire to the spark plug.
7. To attach the auger to the powerhead, in the event this
has not been done, align hole at top of shaft with output
shaft hole. Insert bolt and secure bolt with provided allen
wrench.
NOTE: The ends of the bolt should be flush with auger
collar. Bolt head and thread end should never go
beyond auger collar.
OPERATION
1. Grasp starter handle with right hand and pull out slowly,
until there is tension as you pull. Without letting starter
handle retract, pull rope with a rapid full arm stroke. Let
the starter rope return to its original position very slowly.
When the engine fires or runs, engage the throttle.
NOTE: When attempting to start, DO NOT allow the
recoil to retract on its own, as it may snap back
quickly and cause injury. Repeat this step every
time the starter rope is pulled. Run at full throttle
when possible. Do not let unit idle for extended
periods of time.
2. Repeat start procedure as necessary.
3. To stop engine, turn engine switch to OFF position.
Cold Warm-Up Procedure
When starting the engine in very cold weather, it may be
necessary to “feature” the throttle after starting. This will
allow the engine to warm up and reduce stalling.
IMPORTANT NOTE:
If the engine does not start due to excessive cold
weather conditions, replace the propane cylinder
with a new cylinder that has been stored in a
warm place. Alternately you can move the auger
to a warm place to allow the auger to warm up
sufficiently to start.
IMPORTANT NOTE:
The clutch will transfer maximum power after
about two hours of normal operation. During this
break-in period clutch slippage may occur. The
clutch should be kept free of oil or other moisture
for efficient operation.
Drill holes without placing body weight on the
unit. The auger operates most efficiently with a
shaving action caused by the weight of the unit
itself.
MAINTENANCE AND STORAGE
Auger Maintenance
1. The gear case has 4 oz. of lithium grease installed at the
factory. It is recommended that once a year the gear
case be split and the grease level checked. Add grease
only if level of grease is below top of the gears. DO NOT
OVERFILL.
2. Keep all screws, nuts, and bolts tight.
3. Always replace blade protector when power auger is not
in use.
4. If blade performance decreases, turn unit off and
disconnect spark plug wire. Carefully inspect cutting
edge of blades for any nicks or shiny areas. If blades
show any of these signs, they need to be resharpened or
replaced.