Di 3hnosd, 91 3anoy, Aaivinoaio la aiioaa aanoo aa aaino woez-qz on – Black & Decker 7613-04 Manuel d'utilisation
Page 9: No. 76-230-04 straight & circular guide, Assembly of guide to router base, 3ldnoi ¥1, Assembly of guide to, Base
Attention! Le texte de ce document a été détectée automatiquement. Pour consulter le document original, vous pouvez utiliser le mode "Original".
d i 3Hnosd
*S
0^8|je B siA S8| J0JJ8SS0J smd ‘S0611 80S jns 0pin6 0| J0u6|oj0 no joqoojd
-CJBJ |0 S8U9|{B B SIA S0| J0JJ0SS0p ‘
0pin6 0( }0 0qO0UJ B{ 0JJU0 8DUB}Sip B| J0{60J jnOd
epmo
0 | 0 JJ
-uoo saii
0 |!B B SIA S0 j J0 JJ0 S |0
{¿i
-
6 y) 0 pm6 0 j j0 xy jnsi ‘0 OB|d us apind np
sBd\\
ssi
£1. 3Un0y
xnsiuj 0j JU01AUOO mb uopisod
b
|
uo
|
0 S
(ajn|j0Anoo
abBd
b
|
sp uopBJisnmj jjOA)
01100100
bi
sp
;
uba
0
p
01 jns xnao suBp pos
‘oyoneB 00u6iod
b
|
sp snosssp-us snoji ssi suBp pos ssBp S0|
jsssia
zajjnod snoA
•VION
’(Zl- ‘6p JIOA) 0ldno| B| 0P
0||8UJ8S B| SUBP spinb np SSBp S0P 8J01II inoq 01 J8SSIA
(UOPJOD
0| H3H0NVy830 Jnajoiu a| B3dnOO)
3ldnOi ¥1
3Q 3n3tAI3S
¥1
dOS 30100
00
30¥iN0W
9 1 3anoy
•|U
0UJOUJ 0j
jnod puoj
B SIA
S
0 { J0 JJ0 S SBd 0 M snojoa S0 j suBp sjnoj xnsp
UOJIAU
0 SIA
S
0 j
JSSSjA
} 0 (gt
‘bjl)
0 JJSni|l,nb
j0| SIA S0j
\Q
snojoa S0j jaoBjd :a6e|qiuassv
uoisioajd
spuBjb
0 p siBiq U0 no ssaAjnoui ‘sapojp
sodnoo S
0 | appoBi
\\
saidno} sp sjnsiBsnpn
S0p
s
0 jdnB sjiBjndod sn|d Bj abBsn^p soaid
Bj |S0 ajiBfnojio I B aifojp adnoa ap ap|n6 ai
(j0>|O0a ^ >fOB|g juBiiiBjap
sjjoa
zaqo ju0UJ0|ddns ua)
aaivinoaio la aiioaa aanoo aa aaino woez-QZ
o
N
NO. 76-230-04 STRAIGHT & CIRCULAR GUIDE
(Available at extra cost from your Black & Decker Dealer.)
The STRAIGHT AND CIRCULAR GUIDE is the
most popular device used with the Router. It
enables the operator to make straight, curv
ed
or
angular
cuts
with
convenience
and
accuracy.
TO ASSEMBLE, position nuts and screws as
shown in Figure 16 and thread screws about
two turns into nuts. Do not tighten screws
at this point.
ASSEMBLY OF GUIDE TO
ROUTER
BASE
ITurn
OFF and UNPLUG
Router)
Screw the threaded ends of the guide rods into the Router base as shown in Figure
17. NOTE: The rods can be screwed into the two holes In the side of the Router base
under the left handle or the two holes in the front (side shown on front cover of manual)
of the base whichever is most convenient.
ffsOn
With the guide rods installed, slide the guide over them as shown in Figure 18 and
tighten the
wing screws
on the guide.
The distance between the Router bit and the guide is adjusted by loosening the wing
screws onThe
guide,
sliding the guide inward or outward on the rods, and retighten-
Ing the wing
screws.
FIGURE 18