RCA VR270 - Manuel (Page 15)

Setting Your T\' to the VCR Channel
The “VCR Channel" is the T\' channel you use for
viewing whal the VCR is recording or playing, and
for \ iewing the signal from the VCR tuner when it is
stormed. Your TV must be set to this channel, and the
IVCR! indicator in the display must be on.
Selecting the VCR channel is normally a one-time
procedure, since there is little reason ever to change
it. Proceed as follows;
1. Decide whether you want to view your VCR on
Channel 3 or Channel 4 of the TV'. If one of
these channels is vacant in your area, you should
use it. Otherwise, pick the channel you view less.
2. Set the channel switch (СИЗ/CH4) on the back
of the VCR to whichever channel you have
chosen, and then turn on your TV and tune it to
the same channel. This is the “VCR channel."
Using the TV VCR Button
1. Push the Tk' WCR button on the remote control
so the IVCRI indicator is on. When the indicator
is on. the VCR is in the “VCR mode” and your
TV' must be tuned to the VCR Channel (channel
3 or 4), Your TV will then display w’hatever tape
the V'CR is playing or whatever channel the
VCR is tuned to.
2. Push the TV VCR button on the remote control
again so that the IVCRI indicator is out. When
the indicator is out. the VCR is in the “TV
mode" and your TV w'ill work like it did before
you connected the VCR.
The TV VCR button on the remote control allows
you to record one program with the VCR while you
watch another program on your TV'. To do this, first
put the VCR in the “V'CR mode” (IVCRI indicator
on) and start recording the program. Then press the
TV VCR button to switch to the “TV mode” (1VCRI
indicator out) and tune your TV to the other channel
you want to watch.
Note: Your VCR automatically switches to the “V'CR
mode" (IVCRI indicator on) when you turn it on with
the POWER button, and when you start playing a
tape.
Simplified Installation Qiecktist
This simplified checklist will help you quickly
determine if you have completed all the basic
installation steps. '
( ] Mak^ sure your VCR is connected properly as
explained on pages 4-10. ;
[ 1 Press POWER to turn on VCR.
( ] Set A^ORAZ/C/iTP' switch on the back of the
VCR to The NORM position if you have
connected a home antenna system. Set the
switch to the CiTTF position if you have
connected cable-TV system.
^
[ J Program active charitiels into VCR’s scan list
{press AUTO PROG and wait about one
■ V minute). ■■■', ." "
[ ) £RdS£ or /4individual channels into scan
list as desired. (Detailed instructions:; on
; page 12.) ■■ ■ .
[ J Select "VCR Channel”. . / .
FtT.st setthe CH3/CH4 switch on ihe.backof the
VCR to either charnel 3 or 4 and then tune your
TV to the same channel. This is call<^ the “ VCR;
Channel”.
] Learn how' to use the TV VCR button on the
remote control. ..... ..■ ■■■fy; ....
• When you press the TV VCR button and the
iVCRj indicator in the..di^lay turns iOn, the
VCR is in the “VCR mode” and your TV must
be tuned to the VCR Channel (channels or 4).
Then youriTV will display w'hatever tape the
VCR is playing or whatever chanriei;the VCR
is tuned to.
. . .
When the ¡VCffl indicator in the display is
out,: the ;VC2R is in ¡ the “TV mode” and your
TV will work like it did before vou connected
the VCR. : '
13