Sony WX-GT90BT Manuel d'utilisation
Page 37
37
*1 Does not appear when “SET F/R POS” is set to
“OFF.”
*2 Does not appear when the tuner is selected.
*3 When “SW DIREC” is set to “OFF.”
*4 When “RBE MODE” is set to “OFF.”
*5 When the AUX is selected.
*6 When Bluetooth audio source is activated.
FADER
Adjusts the relative level: “FRONT-15” –
“CENTER” – “REAR-15.”
DM+
*
2
LOUDNESS
(Dynamic Loudness)
Reinforces bass and treble for clear
sound at low volume levels: “ON,”
“OFF.”
ALO
(Automatic Level Optimizer)
Adjust the playback volume level of all
playback sources to the optimum level:
“ON,” “OFF.”
RB ENH
*
3
(Rear Bass Enhancer)
RBE MODE
(Rear Bass Enhancer
Mode)
Selects the rear bass enhancer mode: “1,”
“2,” “3,” “OFF.”
LPF FREQ
(Low Pass Filter Frequency)
Selects the subwoofer cut-off frequency:
“50Hz,” “60Hz,” “80Hz,” “100Hz,”
“120Hz.”
LPF SLOP
(Low Pass Filter Slope)
Selects the LPF slope: “1,” “2,” “3.”
SW DIREC
*
4
(Subwoofer Direct
Connection)
SW MODE
(Subwoofer Mode)
Selects the subwoofer mode: “1,” “2,” “3,”
“OFF.”
SW PHASE
(Subwoofer Phase)
Selects the subwoofer phase: “NORM,”
“REV.”
SW POS
*
1
(Subwoofer Position)
(page 34)
Selects the subwoofer position: “NEAR,”
“NORMAL,” “FAR.”
LPF FREQ
(Low Pass Filter Frequency)
Selects the subwoofer cut-off frequency:
“50Hz,” “60Hz,” “80Hz,” “100Hz,”
“120Hz.”
LPF SLOP
(Low Pass Filter Slope)
Selects the LPF slope: “1,” “2,” “3.”
S.WOOFER
(Subwoofer)
SW LEVEL
(Subwoofer Level)
Adjusts the subwoofer volume level:
“+10 dB” – “0 dB” – “–10 dB.”
(“ATT” is displayed at the lowest
setting.)
SW PHASE
(Subwoofer Phase)
Selects the subwoofer phase: “NORM,”
“REV.”
SW POS
*
1
(Subwoofer Position)
Selects the subwoofer position: “NEAR,”
“NORMAL,” “FAR.”
LPF FREQ
(Low Pass Filter Frequency)
Selects the subwoofer cut-off frequency:
“50Hz,” “60Hz,” “80Hz,” “100Hz,”
“120Hz.”
LPF SLOP
(Low Pass Filter Slope)
Selects the LPF slope: “1,” “2,” “3.”
HPF
(High Pass Filter)
HPF FREQ
(High Pass Filter Frequency)
Selects the front/rear speaker cut-off
frequency: “OFF,” “50Hz,” “60Hz,”
“80Hz,” “100Hz,” “120Hz.”
HPF SLOP
(High Pass Filter Slope)
Selects the HPF slope (effective only
when HPF FREQ is set to other than
“OFF”): “1,” “2,” “3.”
AUX VOL
*
5
(AUX Volume Level)
Adjusts the volume level for each
connected auxiliary equipment:
“+18 dB” – “0 dB” – “–8 dB.”
This setting negates the need to adjust
the volume level between sources.
BTA VOL
(Bluetooth Audio Volume
Level)*
6