Sioux Tools NO. 1 SERIES “1AM” - Manuel

1
Form ZCE509
Date 2003June24/C
Page 1 of 16
Printed In U.S.A.
INSTRUCTIONS FOR NO. 1 SERIES
“1AM” ANGLE TOOLS
Read and understand "Safety Instructions For Air Tools" and these instructions before
operating this tool.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator,
and lubricator will insure maximum output and service life of tools.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 3/8" (10mm) I.D. Extension hoses should be at least 3/8" (10mm) I.D. Use couplings and fittings with at
least 1/4" (6.4mm) I.D.
LUBRICATION
An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04 oz. (1.2cc, 12 to 15 drops) of
SIOUX No. 288 air motor oil into the air inlet daily.
Lubricate the planetary gearing every 150 hours of operation with SIOUX No. 1232A grease. Lubricate the angle head every 8 hours with
Sioux No. 1232A grease. Lubricate positive and adjustable clutches every 25 to 50 hours with SIOUX No. 1232A grease.
Catalog No. *Sound Pressure dBA *Sound Power dBA *Vibration m/s 2
1AMX1201 72.3 83.7 3.3
1AMX1206 72.3 83.7 Less than 2.5
1AMX2106 71.5 82.3 Less than 2.5
1AM1102 72.3 83.7 3.3
1AM1106 72.3 83.7 Less than 2.5
1AM1111 72.3 83.7 3.3
1AM1112 72.3 83.7 3.3
1AM1206 72.3 83.7 Less than 2.5
1AM1211 72.3 83.7 3.3
1AM1311 72.3 83.7 3.3
1AM1402 72.3 83.7 3.3
1AM1411 72.3 83.7 Less than 2.5
1AM1412 72.3 83.7 Less than 2.5
1AM1413 72.3 83.7 Less than 2.5
1AM1511 72.3 83.7 Less than 2.5
1AM1512 72.3 83.7 Less than 2.5
1AM1513 72.3 83.7 Less than 2.5
1AM1611 72.3 83.7 Less than 2.5
1AM1711 72.3 83.7 Less than 2.5
1AM1712 72.3 83.7 Less than 2.5
1AM1713 72.3 83.7 Less than 2.5
1AM2101 71.5 82.3 3.3
1AM2105 71.5 82.3 Less than 2.5
1AM2106 71.5 82.3 Less than 2.5
1AM2201 71.5 82.3 3.3
1AM2202 71.5 82.3 3.3
1AM2205 71.5 82.3 Less than 2.5
1AM2206 71.5 82.3 Less than 2.5
1AM2301 71.5 82.3 3.3
1AM2302 71.5 82.3 3.3
1AM2305 71.5 82.3 Less than 2.5
1AM2306 71.5 82.3 Less than 2.5
1AM2401 71.5 82.3 3.3
1AM2402 71.5 82.3 3.3
1AM2405 71.5 82.3 Less than 2.5
1AM2406 71.5 82.3 Less than 2.5
*per PN8NTC1 *per PN8NTC1 *per ISO 8662
SOUND AND VIBRATION READINGS
Tools left connected to the air supply while making adjustments, changing accessories, or doing any maintenance or service on tool can
start unexpectedly.
Always remove tool from air supply and activate trigger to bleed air line before making any adjustments, changing
accessories, or doing any maintenance or service on tool.
Tools starting unexpectedly can cause injury.